Both centre mounted brake lights and all lights in the rear- driver's side light assembly are out. Where is the fuse that controls these?

Did you check STOP LP fuse 15amp. in the rear fuse block ? Do you know where this is. Fuse Block - Rear Under the rear seat, on the left side of the floor pan.
The STOP LP fuse in the fuse block - rear supplies battery positive voltage to the normally open stop lamp switch. When the driver presses the brake pedal, the switch contacts close. The battery positive voltage flows to the left stop lamp assemblies, to the right stop lamp assemblies and to the center high mounted stop lamp (CHMSL). The left stop lamp and the CHMSL have ground at G402. The right stop lamp has ground at G401.
Did you check for power at the stop lamp switch ? both in an out of the switch with brake pedal pressed ?
Did

Kevin , this is a very complex way of stoplamp control , I will post GM service Description and Operation of how they work an let you deside if you want to tackle this ! Do the center high mount brake lights work ?
The brake pedal position sensor is a resistive device used to sense the action of the driver's application of the brake pedal. The brake pedal position sensor provides an analog signal that will increase as the brake pedal is pressed.
The brake pedal position sensor receives both a 5-volt reference voltage and a low reference signal from the electronic brake control module (EBCM). When the brake pedal is pressed, a variable signal is applied from the brake pedal position sensor to the EBCM through the brake sensor signal circuit. The fuse block left rear supplies battery positive voltage to the bass relay switch through the BASS fuse. One side of the bass relay coil is permanently grounded at G402. The EBCM supplies voltage to the bass relay coil upon receiving the signal from the brake pedal position sensor. The switch contacts of the bas relay close and battery positive voltage is applied through the bas relay switch to the center high mounted stop lamp (CHMSL), and to the turn signal/hazard flasher module through the stop lamp switch signal circuit. The ground for the CHMSL is applied from G402. The turn signal/hazard flasher module then supplies voltage to the left and right stop lamps in the tail lamp assemblies that have ground at G401 and G402. For export vehicles the stop lamps receive battery positive voltage directly from the bass relay.

There could be a code stored in the EBCM - electronic brake control module - DTC B3903 Stop Lamp Relay Circuit
DTC C0278 Brake Pedal Position Sensor Not Calibrated
there are several other codes that pertane to the brake lights . you could try Replaceing the bas relay !
Fuse Block - Left Rear
In the passenger compartment, under the left side of the rear seat at carpet.

There is only one fuse for the brake light, so if the passenger side is working, the fuse is OK. You most likely have a bad bulb, bad bulb socket or a wire issue. The circuit board that all of the rear light are mounted to also has had problems in the past.
BTW - the fuses for the rear light are under the rear seat.

Hi there,

Your Brake Light fuse (10A) is located in the driver's side kick panel (see diagram below).

If your 10A fuse is OK, then you may have an issue with your Brake Switch (mounted to your brake pedal assembly).

Instrument Panel Fuse Block
The instrument panel fuse block access door is
located on the driver side edge of the instrument panel.

Pull off the cover to access the fuse block.

The vehicle may not use all of the fuses shown.

Fuses Usage
1 Rear Seats
2 Rear Accessory Power Outlet
3 Steering Wheel Controls Back light
4 Driver Door Module
5 Dome Lamps, Driver Side Turn Signal
6 Driver Side Turn Signal, Stop lamp
7 Instrument Panel Back Lighting
8 Passenger Side Turn Signal, Stop lamp
9 Passenger Door Module, Driver Unlock
10 Power Door Lock 2 (Unlock Feature)
11 Power Door Lock 2 (Lock Feature)
12 Stop lamps, Centre High Mounted Stop lamp
13 Rear Climate Controls
14 Power Mirror
15 Body Control Module (BCM)
16 Accessory Power Outlets
17 Interior Lamps
18 Power Door Lock 1 (Unlock Feature)
19 Rear Seat Entertainment
20 Ultrasonic Rear Parking Assist, Power Liftgate
21 Power Door Lock 1 (Lock Feature)
22 Driver Information Centre (DIC)
23 Rear Wiper
24 Cooled Seats
25 Driver Seat Module, Remote Key less Entry System
26 Driver Power Door Lock (Unlock Feature)

When you are talking about "indicators" we could assuming that your are refer about signal lights. This work with "flashers" devices.

For 1996 Audi A4 2.8L SFI 6cyl the Flasher is located in front seating area, driver side, under dash, behind dash lower panel, mounted above driver side of steering column.

About generic fuses, open the driver side door. Remove panel on left side of dash. Fuse box is behind panel:

Fuse # / Description / Amps
1 / Heated washer jets / 5
2 / Turn signals flasher unit / 10
3 / Headlight washer, illumination of glove compartment, engine compartment, climate control, automatic transmission, instrument cluster / 5
4 / License plate light / 5
5 / Instrument cluster, seat heating, test connection for cruise control, bulb monitor for auto-check control, Automatic transmission display, switch lighting, mirror switches and actuators, airbag warning light, outside temperature indicator, Climate control / 10
6 / Central locking system / 5
7 / Anti-lock brake system / 10
8 / Vacant
9 / Mirror heating / 10
10 / Vacant
11 / Cruise control (automatic transmission) / 5
12 / On board diagnostic system / 10
13 / Brake lights / 10
14 / Interior lights, reading lights, anti-theft alarm system, vanity mirror / 10
15 / Instrument cluster, power windows, climate control, automatic transmission / 10
16 / Anti-lock brake system, Anti-Slip-Regulation / 5
17 / Heated door locks / 10
18 / High beam right / 10
19 / High beam left / 10
20 / Low beam right / 15
21 / Low beam left / 15
22 / Tail and side marker right / 5
23 / Tail and side marker left / 5
24 / Wiper and washer system / 25
25 / Blower for heating, climate control / 30
26 / Rear window defogger, mirror heating / 30
27 / Rear window wiper / 15
28 / Fuel pump / 15
29 / Engine timing / 20
30 / Sun roof / 20
31 / Tail lights, cruise control, automatic transmission / 15
32 / Engine timing / 20
33 / Cigarette lighter / 15
34 / Engine timing / 15
35 / Trailer receptacle / 30
36 / Fog lights / 15
37 / Radio / 20
38 / Luggage compartment light, central locking system / 15
39 / Emergency flasher / 15
40 / Horn / 25
41 / Anti-lock brake system / 25
42 / Vacant
43 / Vacant
44 / Seat heating / 30

Hope this helps (remember to rate and comme this free answeer).

just a thought,has someone put double sided tape on the mounting bracket to stop vibration.....i would....

Make sure the fuses are good.There is a fuse for left and right brake lights.The fuse blocks are under the hood and there`s also one under the drivers side rear seat.If the fuses are good then remove the rear lamp assembly and check the bulb.I believe there are 2 screws and then just pull lamp assembly out.Hope this helps.Good luck.

The high mount brake light has its own fuse, so check that first. The high mount bulb is generally a stabdard type (there may be more than one bulb) or you can replace with an LED. As for the left rear bulbs not working when depressing brake pedal, check the bulbs again for any spring that may be broken. If the bulbs are still good, make sure there is sufficient contact with the socket. If still not working, have someone check it out further.

your truck has fuses for the rear and high mount brake light in the fuse box in the side of the dash when you open the drivers door