Question about 2000 Lincoln Town Car

1 Answer

Need to find a way to take off the drivers side window motor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 2,989 Answers

Motor

  1. Disconnect the negative battery cable.
  2. Remove the door trim panel and watershield.
  3. Detach the motor wires at the multiple connector.
  4. Remove the motor retaining screws using Torx® drive bit set D79P–2100–T or equivalent, and separate the motor from the bracket and cable drum housing.
  5. Remove the motor from inside the door.
To install:
  1. Position the motor and drive to the cable drum housing and motor mounting bracket. Install the 3 motor screws and tighten.
  2. Connect the power window motor wiring.
  3. Connect the negative battery cable.
  4. Check window operation.
  5. Install the watershield and door trim panel.

Door Panel
  1. Disconnect the negative battery cable.
  2. Snap out the two door pull strap retaining screw covers. Remove the screws.

CAUTION To avoid breakage of the door pull covers, insert a small screwdriver diagonally between the pull strap and chrome bracket. Snap out both sides then remove.


  1. Remove the two screws on the front and rear side of the front door trim panel.
  2. Using the trim pad removing tool, pry the trim panel retaining clips from the door inner panel.

NOTE Do not use the front door trim panel to remove the trim clips from the door inner panel. Replace any bent, damaged or missing push pins.


  1. Remove the window regulator switch housing from the back of the front door trim panel. Lift up the housing and disconnect all connectors from the switch housing.
  2. Disconnect the driver seat regulator control processor switch if equipped.
  3. Twist out the interior lamp wire assembly.
To install:
  1. Ensure that the plastic watershield is secured to the door .
  2. Position the front door trim panel to the door. Connect the interior lamp wiring.
  3. Align door lock side to its mating slide on the sheet metal.
  4. Snap in the front door trim panel. Ensure all retainers fit properly. Install the two retaining screws on the front and rear side of the front door trim panel.
  5. Connect the driver seat regulator control processor, if equipped.
  6. Position the window regulator control switch housing and connect the switch connectors. Install it to the front door trim panel by snapping it in, or by installing the screw at the rear.
  7. Install the two retaining screws and pull strap covers.
  8. Connect the negative battery cable.
need to find a way to take off the drivers side - 053777a.gif

Posted on Aug 27, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver side window stopped working


most of the time driver side windows switch be the first switch to wear out.try removing window switch work switch while moving the wires see if window try to go up, if yes, window switch broken.if switch not broken check see if power going to window motor when you work the switch you need a test light or digital volt meter to check to see if power going to power window motor.if power going to power window motor, either window binding or power window motor faulty. make sure driver side window master switch not locked out.if no make sure all the other power windows work if not you have blowed fuse.

Nov 26, 2012 | Hyundai XG350 Cars & Trucks

2 Answers

Driver side power window doesn't work. The passenger side worked for a while then, it stopped working also. I found thecircuit breaker box and pushed in the breaker for the windows. Now, the passenger...


No I would think a 20 year old van needs a drivers side window motor ,,Its the most used window in the Van, also a new window switch to control the motor

Mar 13, 2011 | 1995 Pontiac Trans Sport

1 Answer

Driver side window motor not going up or down


You may be having problems with the motor drawing too many amps and kicking out a circuit breaker. If this is the case, you will have to replace the window motor.Check the window switch too.It can also be the cause of window not working.You can check both the window as well as switch with voltmeter or a test light to confirm which part is faulty. The window motor is a 12 volt electrical part.So check for the 12 volt to the motor connections.If the voltage is low then its faulty motor and has to be replaced. ------------- Also in your question comment you have mentioned that driver side window motor not functioning.So in that case before going for new replacement motor,i suggest to connect the passenger side motor to driver side motor connections and check.If the window functions with passenger side motor connected then its a faulty driver-side motor,but if the window not working with passenger side motor connected , then its not the faulty motor but the faulty driver side window operating switch.It has to be replaced.But in some cases it has also seen that parts like motor as well as switch are ok but the problem relates to short in wiring or the wires getting loose between switch to regulator or switch to motor.So confirm this possibilities also before going for any kind of part replacements. --------------- Keep updated with any more queries.Thanks.

Oct 14, 2010 | 1999 Chevrolet Malibu

1 Answer

My driver side front window does not come down but the passanger side front and back and driver back do go up and down. Do i need to change the power window motor or is it the window regulator for driver...


regulator usually wears out and breaks or gets bound and burns up motor, change them both if available. Good sign of bad regulator is sloppy window in track, or window off track. I always replace them together if they are available. it is possible that you just need a switch, but most likely the reg/motor.

Apr 15, 2010 | 2000 Daewoo Nubira

1 Answer

I replaced the driver's side window motor because


I don't know everything there is to know about window motors, but I have seen this before, both mine went out at the same time, not together but a couple weeks apart, like they were dated. Anyway, I replaced both motors, then both operators. Now they both work fine. I would hang on to the old motor, you never know, it might be good, You might have a bad switch on the door, I had to take my switches apart on my other truck and clean the contacts, got both motors working again, Hope this helps.

Mar 20, 2010 | 2003 Hyundai Tiburon

1 Answer

The window on the driver's side will not go up or down and will not stay up.


Need to check power to switch - then to window motor -- to do this you have to remove drivers door panel and use and test light with the ignition switch in the on postion. With test light connected to window motor, press switch up or down , if light comes on and motor does not - replace motor - if no power at motor replace switch..

Dec 02, 2009 | 2002 Dodge Durango

3 Answers

The drivers side window stoped working on my 2004 silverado the passenger side works fine


Try the fuse. The switch may be faulty so check by removing the inner door panel and connecting a 12v battery via two wires to the motor that winds the window up and down. If it goes up and down it's probably the switch which may just need a clean on the terminals.

Nov 01, 2009 | 2002 Chevrolet Silverado 2500HD

2 Answers

Windo motors wont work


The driver side window switch is the master switch, the power or input to either roll the window up or down goes thru that switch. Double check all the connections on the back of the driver side window switch are good. With a DVOM you can also check to see if 12v are even getting to the master switch in the first place. If you aren't even getting power to the main power window switch you could've blown the power window fuse.

Jul 17, 2009 | 1994 Oldsmobile Silhouette

1 Answer

Electric window motors


They should be the Same Motors.

Jan 23, 2009 | 2005 Nissan Xterra

3 Answers

97 cadillac deville power window motor replacement drivers side


The motor sit on a gear stem you will have to wiggle it a little to get it off the magnet inside is holding it to the window frame just use a little pressure to remove.

Jul 16, 2008 | 1997 Cadillac DeVille

Not finding what you are looking for?
2000 Lincoln Town Car Logo

555 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

gerry bissi

Level 3 Expert

4388 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...