Question about 1998 Chevrolet Corvette

1 Answer

I WANT TO REMOVE THE ENTIRE - POP UP HEAD LIGHT FROM "98 CORVETTE

I WANT TO REMOVE THE ENTIRE - POP UP HEAD LIGHT ASSMBLY FROM MY 1998 CORVETTE. NOT REPLACE A BULB BUT THE ENTIRE ASSEMBLY, SO I CAN INSTALL A ""FIXED"" HEAD LIGHT SYSTEM. PLEASE ATTACH A STEP BY STEP PHOTO SHOWING THE REMOVAL OF THIS ENTIRE POP UP HEAD LIGHT FROM THE CAR. THANKS IN ADVANCE

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 191 Answers

Why not just disable the motors while in up position?

Posted on Aug 25, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove 98 explorer taillight


Very simple procedure. Open the hatch and you'll see two phillips head screws at the top of the tail light housing. Remove those and pull straight out on the entire housing. It can be a little stubborn, so may need to rock it back and forth or even gently pry the edges to loosen it. By the way, this is the only way to get at the bulbs for replacement.

Feb 15, 2015 | 1998 Ford Explorer

1 Answer

98 corvette headlights not working


If you can verify current going out of the main dash switch towards the headlamps, then I would go relay hunting. My guess is the switch, since the brights and fog lamps work on demand (dimmer switch pulled).

Jul 09, 2012 | 1998 Chevrolet Corvette

1 Answer

Have a "98 A/T


10w30 will be fine on any broken in engine. The first 10000 miles 5w30 is recommended. On the very bottom side of the engine's oil pan will be the bolt to remove to drain the oil

Aug 08, 2011 | 1998 Chevrolet Corvette

1 Answer

98 chev corvette auto transmission will not shift into 3rd gear or overdrive


I would start by checking the fluid level in your transmission. If it is fine, then it's possible one of the solenoids in the transmission is going bad. Is the check engine light on? Goodluck

Mar 27, 2011 | 1998 Chevrolet Corvette

1 Answer

How to replace right rear turn signal bulb. doesn't look like I can reach the bulb without removing the entire assembly. Looks like I need a tool that fits on a star head to remove it. Correct?


open the trunk lid and remove the screws. If they are star head screws, you'll need that typ of tool. The assmbly should easily be removed and you'll have access to the bulbs

Dec 17, 2009 | 2005 Pontiac Grand Prix

2 Answers

98 Blazer...constant heat from heater, both dash vents and floor vents REGARDLESS of heat setting on dash thermostat


this problem is caused by a failed HVAC temperature control blend door electric actuator, to replace this part you must remove the entire dash assmbly

Sep 15, 2009 | 1998 Chevrolet Blazer

1 Answer

Removing the whole pop head lights assembly from my 1997 corvette


Raise the headlights, either with the switch or manually by turning the knob on the headlight motor counter-clockwise.
Unplug the lights NOW to avoid an accidental closing on your fingers,
Remove the 3 philips screws holding the black plastic surrounding the headlights, and slide it forward, there is a small clip on the top that helps hold it to a corresponding clip at the top of the headlight,
Look inside the cavity and you can see the 5 nuts/bolts ( 6 on later years ) that need to be removed,
If you are on the driver's side you can now remove the whole assembly, on the passenger's side you must first unplug the headlight door control module.

Aug 25, 2009 | 1998 Chevrolet Corvette

1 Answer

HOW DO I INSTALL UNDERHOOD LIGHT ON 1998 CORVETTE


assuming you mean replacing the bulb? about $2.00 a bulb
the bulb is push and twist, open the hood and remove the plastic cover then remove the bulb by pushing it down and twist it a little till it pops out. I see only one light , I think my 1994 vette has two
photo
hope this helps
Eric

I’m happy to help further over the phone at https://www.6ya.com/expert/eric_ab7c09ec01841771

Aug 25, 2009 | 1998 Chevrolet Corvette

2 Answers

Wipers going when they are off


Check under the dash or on the sides of the dash with doors open, or under the hood in a box marked fuse relay. In most GM cars and trucks these are the places where thay stash the fuses

Dec 29, 2008 | 1998 Chevrolet Corvette

Not finding what you are looking for?
1998 Chevrolet Corvette Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...