Rear back door will not work with central locking system

1. Replace battery in remote
2. Replace sensor at rhf door lock (it is inside of door)

check central locking system fuse it controls all door locks and other acessories.need go to dealership buy remote keys..

This worked for me on 2008 Mk5 Golf, after the rear passenger door would not open fro outside or inside.

Hold the inside door latch open and keep it extended, then with the key fob open and close the door locks (still holding the inside latch open). Keep locking and unlocking the door, then it made a kluck and it released.

For Doors not getting open with remote or key problem, there are help links provided below. Click the link below to go through its procedure and troubleshoot the problem: ----
Drivers side front door will not open from inside or outside?

http://technoanswers.blogspot.com/2012/01/ford-f-350-crew-cab-drivers-side-front.html

----------

Car door will not close?
http://howtobyme.blogspot.com/2011/11/car-door-will-not-close.html

--------

All power door locks not working?
http://howtobyme.blogspot.com/2011/11/all-power-door-locks-not-working-on_14.html

----------

Repairing car Door lock Actuator?
http://howtobyme.blogspot.com/2011/11/repairing-car-door-lock-actuator.html
---------------
How to Access car door panel?
http://howtobyme.blogspot.com/2011/11/how-to-access-car-door-panel.html

----------

Vehicle door panel components?

http://howtobyme.blogspot.com/2011/11/vehicle-door-panel-components.html

---------
Truck Door will not close?

http://schematicsdiagram.blogspot.com/2011/12/ford-truck-door-will-not-close.html

-----------
Where is Cars Door control Module located?

http://schematicsdiagram.blogspot.com/2011/12/where-is-cars-door-control-module.html

--------
Power door locks not working?

http://schematicsdiagram.blogspot.com/2011/12/power-door-locks-not-working.html

-----------
Door ajar light stays on?

http://technoanswers.blogspot.com/2012/01/door-ajar-light-stays-on.html

----------
Door locks not working?

http://technoanswers.blogspot.com/2012/01/door-locks-not-working-on-ford-explorer.html

----------
Front Door dis-assembly diagram?

http://repairhelpcenter.blogspot.in/2012/02/front-door-dis-assembly-diagram-for.html

---------
Rear Door dis-assembly diagram?

http://repairhelpcenter.blogspot.in/2012/02/rear-door-dis-assembly-diagram-for.html

--------
How to test Power door locks?

http://repairhelpcenter.blogspot.in/2012/02/how-to-test-power-door-locks.html

--------
Doors will not open with Remote?

http://schematicsdiagram.blogspot.in/2012/02/lexus-doors-will-not-open-with-remote.html

--------

How to replace Door Hatch ?
http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-hatch-on-acura-integra.html

---------

How to remove Doors?

http://repairhelpcenter.blogspot.com/2011/11/how-to-remove-doors-on-acura-integra.html

-------`-

How to Replace Doors?
http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-doors-on-audi-a4-and-vw.html

--------

Remote will not unlock Rear door?
http://schematicsdiagram.blogspot.com/2011/12/remote-will-not-unlock-rear-door-on-gmc.html

--------

Door locks or windows not working on car?
http://schematicsdiagram.blogspot.com/2011/07/door-locks-or-windows-not-working-on.html

----------
Central locking not working?

http://schematicsdiagram.blogspot.in/2012/03/this-is-how-system-operates.html

This will help.

Thanks.

Your remotes may need to have batteries replaced and re-programmed.

check lock buttons on doors and keyfob for stuck button

2006 Nissan Pathfinder rear passanger doors don't open unless opened from insinde handle first. Then will open all the time until central locking is used then same problem occurs

My 1998 passat done the same, try remove the drivers side window/childlock control on the armrest and clean the multipoint switch as that got my drivers side door opening/closing on the fob as well as the passenger rear door unlocking and working again as it was deadbolted and would not open inside or out.

To carry out this procedure you need to have one working key and one key which requires programming. It may help sometimes to hold the key close to the rear view mirror as this is where the sensor is located in most models. 1. With both keys, get in the car and close all windows and doors. 2. Put working key into the ignition and turn to position 1 (the accessories should turn on) (try also position 2) 3. Turn the key back to position 0 and take the key out of the ignition. 4. Using the working key, hold down the unlock button, press the BMW logo (lock button) 3 times, and release the unlock button. Doors should lock and unlock. 5. With the new key, hold down the unlock button and press the BMW logo (lock button) 3 times and let go of the unlock button. Doors should lock and unlock and you're done!! If not working try the following PREPARATION 1. Close all doors, trunk, hood and sunroof. 2. The security system must be in 'disarm' mode. The key must be removed from the ignition key slot. ENTER CODE LEARNING MODE 3. Open trunk and leave it opened. 4. Open the drivers door and sit in the drivers seat. 5. Close the drivers door. 6. Cycle the ignition switch 5 times between the 'OFF' position and position 2,(ignition 'ON', all dash warning lamps will illuminate). The red status LED will illuminate continuously, and the siren will 'chirp' once, to indicate that the code-learning mode has been initiated. ?Do No start the engine.? The Ignition switch cycling in step #6 must be performed within 10 seconds. The sequence in steps #1-#6 must be performed within 45 seconds. REGISTER/DELETE ID CODE(S) 7. Open drivers door, (remain seated in the drivers seat) 8. Close the drivers door. 9. Press and release any button on the remote you wish to register in the system. The status LED will shut off momentarily to indicate that one code has been registered. 10. Repeat steps 7 thru 9 to register the three ID codes. It is possible for the system to memorize a total of 4 different ID codes. As a new code is initialized into the memory, the oldest code is automatically deleted. If you had lost your remotes and wished to delete the lost remote ID codes from the memory, you could initialize the ID codes from a newly purchased replacement transmitter four times thereby deleting the previous ID codes from the system memory. EXITING CODE - LEARNING MODE: 11. Open drivers door, and exit from the vehicle, leaving the door opened. 12. Close trunk. 13. Close drivers door. The LED will turn off and the siren will 'chirp twice. 14. The initialization procedure is now completed; Test all remotes to confirm operation. If this doent work your alarm/central lock needs to be reset