2007 tahoe seats

If you have third row. Look at the slots in the floor. If the outer slots are the same distance apart, front and back, then you can. Some vans you can, but some the captains chair are spaced further apart.

Hi Amy, I'm AL the owner of Big As Auto Repair.
I look forward to helping you with your problem!

Amy, the middle bench seat is held in with four mounting bolts that must be removed from the legs of the seat. If you should need further assistance click here:
Auto Repair

Yes of course you can remove the seat. There is a pull at the rear of the seat in the middle (down on the frame) The pull is a loop of material. You need to pull that up with solid force, this will release the lock so you can tilt your seat forwards. Once the seat is rotated forward enough, you will be able to lift the seat out.
I leave my seat out behind the drivers seat most of the time for easy access into the back and just putting stuff in the car. Also, the side clearance height is higher than the rear hatch height.

You can buy a 2008 Tahoe with bucket seats but I'm afraid I cannot find any information about switching out the seats. -------------------------------------------------------------------------------
ELM 327 1.5V USB CAN-BUS Scanner

Did you ever find a solution to this problem? I too am looking to convert to bench seat in middle row

It depends on your seating. My Windstar has bucket seats, and the very back is a bench type 3 seater. The middle row normally has 2 shoulder/lap belts. It really depends on the perks that the original owner opted for upon purchase. For instance my driver seat has a button on the right side to adjust the lumbar area of the seat.
Checking CarFAX will let you know if the vehicle has ever been in a major accident. Most people do not realize that after an accident, seat belts and their anchors should be replaced.

On the front corner of your Acadia's middle row seats, you will notice a plastic covering - pull on it - the plastic pin holding it back will fall off, and you can then remove it. Now, the bolts that need to be removed to unmount the seat, are clearly visible.
Also, experts recommend that it would be best if the doors are removed to give enough space to manage the task. Removing the doors may take you about 10 to 15 minutes, whereas seat removal can take 20 to 25 minutes.

Yes...you can. I did this in my 05 Grand Caravan. We found ours at a local junk yard. It cost us 200 and even matched pretty well with the current benches. Just call around to your area junk/salvage people.

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.

I don't think the seat can be split! I am looking for '01 -02 LT or SLT center row buckets, if they will fit the floor brackets - my dealer cannot determine if the attachment is workable! (Someone, please help) These seats recline (not fold flat) and would allow plywood to be carried vertically between the seats! I have already installed floor brackets and belts for a '4th row' in my 8 passenger to carry plywood on top of the seats, but it is 'mickey mouse'.