Show me the fireing ordor

Found this firing order.
As far as the sensor, you talking about 02 sensor? Bank one has the number 1 cylinder, bank 2 is the other bank, sensor 1 is the first sensor you come to, in the exhaust.

Here's a link to your firing order,cylinder 1 is bank 1. Specifications Firing Order AutoZone com

It is the one that is on the driver's side, first one in the exhaust stream before the catalytic converter.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/michael_2496c4f07ad24453

Hi James,here's a link to your firing order,cylinder two is bank two and sensor one is the oxygen sensor screwed into the exhaust manifold on that side.

Here's your firing order cylinder one is bank one,sensor two is at the catalaytic convertor on that side,which is the passenger side,the oxygen sensor.

P0141 indicates oxygen sensor 2 in bank 1. Bank 1 is on the side of the engine where the first cylinder is.

Your firing order (and the location of your cylinders) can be found here:
http://autorepair.about.com/library/firing_orders/bl-fo-0286.htm

And further reading on the code you pulled can be found here:
http://www.obd-codes.com/p0141

On all cars, the bank 1 is where the first piston is...Your firing order on that car which is the first piston...Buy a chilton or a repair manual for your car and it will tell you which firing order your motor has....Its usually on the right hand side...Passenger side...Rule of thumb if you look at the spark plugs the one closest too you is usually the first piston....Bank 1 is located on the same side as the first piston...I hope this helps...

As of 1996,all cars sold in the US were required to have an OBD-II computer interface port.
You may want to go to Advance Auto Parts, AutoZone, or Pep Boys, and get a free read
of the code(s) that you computer may be posting to help with your diagnosis.

The code coming from your vehicle's computer may be one or more of:

P0130 02 Sensor Circuit Malfunction (Bank I Sensor 1)
P0131 02 Sensor Circuit Low Voltage (Bank I Sensor I)
P0132 02 Sensor Circuit High Voltage (Bank I Sensor 1)
P0133 02 Sensor Circuit Slow Response (Bank 1 Sensor 1)
P0134 02 Sensor Circuit No Activity Detected (Bank I Sensor 1)
P0135 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0136 02 Sensor Circuit Malfunction (Bank I Sensor 2)
P0137 02 Sensor Circuit Low Voltage (Bank I Sensor 2)
P0138 02 Sensor Circuit High Voltage (Bank I Sensor 2)
P0139 02 Sensor Circuit Slow Response (Bank 1 Sensor 2)
P0140 02 Sensor Circuit No Activity Detected (Bank 1 Sensor 2)
P0141 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0142 02 Sensor Circuit Malfunction (Bank I Sensor 3)
P0143 02 Sensor Circuit Low Voltage (Bank I Sensor 3)
P0144 02 Sensor Circuit High Voltage (Bank I Sensor 3)
P0145 02 Sensor Circuit Slow Response (Bank 1 Sensor 3)
P0146 02 Sensor Circuit No Activity Detected (Bank I Sensor 3)
P0147 02 Sensor Heater Circuit Malfunction (Bank I Sensor 3)
P0150 02 Sensor Circuit Malfunction (Bank 2 Sensor I)
P0151 02 Sensor Circuit Low Voltage (Bank 2 Sensor I)
P0152 02 Sensor Circuit High Voltage (Bank 2 Sensor 1)
P0153 02 Sensor Circuit Slow Response (Bank 2 Sensor 1)
P0154 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 1)
P0155 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
P0156 02 Sensor Circuit Malfunction (Bank 2 Sensor 2)
P0157 02 Sensor Circuit Low Voltage (Bank 2 Sensor 2)
P0158 02 Sensor Circuit High Voltage (Bank 2 Sensor 2)
P0159 02 Sensor Circuit Slow Response (Bank 2 Sensor 2)
P0160 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)
P0161 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
P0162 02 Sensor Circuit Malfunction (Bank 2 Sensor 3)
P0163 02 Sensor Circuit Low Voltage (Bank 2 Sensor 3)
P0164 02 Sensor Circuit High Voltage (Bank 2 Sensor 3)
P0165 02 Sensor Circuit Slow Response (Bank 2 Sensor 3)
P0166 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)
P0167 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 3)

Note: "Bank 1" is the side of the engine with cylinder 1. "Bank 2" is the other side.

P0300 - Random/Multiple Cylinder misfire detected
P0301 - Cylinder 1 misfire detected
P0302 - Cylinder 2 misfire detected
P0303 - Cylinder 3 misfire detected
P0304 - Cylinder 4 misfire detected
P0305 - Cylinder 5 misfire detected
P0306 - Cylinder 6 misfire detected
P0307 - Cylinder 7 misfire detected
P0308 - Cylinder 8 misfire detected
P0313 - Misfire detected with low fuel

Maximas with the VE30DE and VQ30DE engines use a distributorless ignition system that is controlled by the Engine Control Module (ECM). The ECM receives a signal from the crankshaft sensor (the CPS - Crankshaft Position Sensor), and processes the signal based on inputs
from other various engine sensors, including the Oxygen sensor.
(this is the role of the O2 sensor in ECM operation).
Then the ECM sends signals to each of the individual coils in the proper firing order.
This system is more efficient than a distributor, and has fewer moving parts. The high voltage coils are directly attached to each spark plug, allowing a higher energy spark within the cylinder. A high energy spark means a faster, more thorough burning of the air/fuel mixture, which produces more power and lower emissions.


SECONDARY SPARK TEST - works for all cars, including Maxima.


1. Remove the spark plug.

2. Install the spark plug to the ignition coil/coil pack, then attach the coil wiring.

3. Ground the plug at a good ground location on the engine.

4. Crank the engine and check for spark.

5. If spark occurs, the ignition system is functioning properly.

6. If no spark exists, test the ignition coil/coil pack, power transistor and related wiring.

----------------------------------------------------------------------------------------------------------------------------
HEI Ignition Spark test - works for all cars, including Maxima.

The next level test you may want to try is a HEI (high energy ignition) spark tester kit. Cost is
about $30 at most auto parts stores. Harbor Freight Tools sells a chinese equivalent for about $16.
Place the spark tester on each of the spark plugs, and watch as the little light in the tester will
light up each time the spark plug is fired by the computer. You can actually see weak or
intermittent sparking as the motor runs - you can tell by the relative strength of the light as
you compare the intensity and duration of the light across all 6 cylinders.

If your problem were the alternator (or its built-in voltage regulator), your battery would not be
getting a proper charge, and you
wouldn't be able to start the car after a drive, since the battery would have been drained during the
drive - normally, the alternator will both charge the battery and run all electrical
features of the car during a drive.

To test your alternator, place your DMM (digital multimeter) across the battery terminals while the
car is running - it should read 13.5VDC to 14.5VDC. With the car off, you can test your battery
voltage with the same DMM - it should read 12.65 VDC (for a fully charged battery).

Alternatively, you can take your car to Advance Auto Parts, AutoZone, or Pep Boys, and they'll
attach their "charging system tester" to your car and give your car a nice test for free.
I do this with my customers' cars just to get that nifty printout of the problem. Its nice
to show a vehicle owner somethng in black & white when I'm recommending a new charging
or ignition system component (some of which can be a bit pricey).

if i am not mistaken , bank 1 is the closest 02 sensor to the engine, look down onto your exhaust system , and follow it to the closest 02 sensor to the engine. and check the wire connection to it to make sure it is not frayed or disconnected.

Bank 1 02 is on the exhaust side that cylinder 1 is on bank 2 would be the other there should be bank 1 sensor one and bank 1 sensor 2 and on the other side it is bank 2 sensor 1 and sensor 2 with that in mind get a firing order from a auto part store bank 2 should be on the driver side sensor 1 is before the cat sensor 2 after the catalytic convertor