Question about Peugeot 307

1 Answer

How to release stuck seatbelt in middle back of Peugeot 307

I can't access any part of the mechanism and it's totally jammed.

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Peugeot Master
  • 2,910 Answers

Best to replace it, even if it was repaired could you rely on it in a crash.

Posted on May 03, 2019


6 Suggested Answers



Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017



  • 324 Answers

SOURCE: Volvo V70 rear seatbelt jammed

i know this sounds rough, but pull the seat belt with both hands as hard as you can, this will more than likely free the seat belt, some of the seat belt may have jammed in the gear inside the roller box.......

Posted on Nov 26, 2008


  • 1 Answer

SOURCE: Volvo V70 rear seatbelt jammed

you can remove the bolt that holds the seatbelt to the floor by pulling off the seatpad where the belt goes to the floor and then raise the seat and the belt should reset. this happens on my passenger side rear seat.

Posted on Dec 23, 2008

Wahs Team

  • 215 Answers

SOURCE: "when do i change the cam belt on a peugeot 307 sw diesel"

usually you should do it for peugeot diesel at 122000 miles along with water pump and the tensioner roller that runs under the cambelt too. But to be on the safe side do it at 100000 and save the fortune.
It took me (DIY job) about 6-8 hours as i wanted to save 450 pounds.

Posted on Sep 04, 2009


  • 2 Answers

SOURCE: How do you fix a stuck seatbelt in front seat

this is a simple repair many dont know. remove or pull off plastic pillar post cover, seatbelt probably twisted inside. twist it back around so it runs flat and lube slightly with a light lube spray on metal gearing. i had the same problem w mine pk

Posted on Jan 20, 2010


  • 6 Answers

SOURCE: peugeot 307 1.6

peugeot and citreon cars do bite high generaly, it is hydaulic there is no adjustment. but it also depends on how high it is ?? does it slip if you slightly rest your foot on whilst driving?? they do have a problem with the bearings going through the cover as it is the same bearing as a HDI . but you woud notice this as a different problem. ie noise or vibration on pedal. call me for more info .. paul @ the clutch centre..01527 64440 07790438337

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can the torque converter keep the motor from turning as in locked up

for this to happen will mean a total failure in the converter where the fins/blades have come apart and are jamming on each other
basically I would be looking for mechanical failure in the engine.

Mar 13, 2015 | Cars & Trucks

1 Answer

How do you repair the tilting front seat tilting mechanism is jammed, can you illustrate how i can gain access to repair

ok on the side were the tilt handle is un bolt that theres a cable that should be hooked up to it it might be jammed or it might be off that could cause it not to come back

Nov 01, 2014 | 2007 Ford Fiesta 1.4

1 Answer

Fortuner back door is jammed shut

I'm not familiar with your specific car, but if you have a tailgate, there will be a pane you can remove on the inside that will allow you access to the mechanics of the door release. You can operate the rods through the access holes.

Mar 28, 2014 | Toyota Fortuner Cars & Trucks

1 Answer

When passing the car continued to accelerate , had to stand on brake engine conntiued to race and was shut down, engine restarted with no appearent damage. but we are now totally unsure about driving the...

If you are not at least a shade tree mechanic, i recommend that you find a mechanic to take a look at the throttle linkage for obstructions or other abnormalities, and also to take a look at the pedal, because sometimes a dangling cable from the dashboard, or the floor mat can jam the pedal. You are right about being cautious over driving the car to the shop.

Jun 16, 2011 | 2002 Buick LeSabre

1 Answer

How do you replace the driver side door latch on a 2000 nissan sentra,cant see how it is installed and get hands in there. is there a certain way of doing this?

When you say door latch, what exactly are you referring to? There is the locking latch, inner and outer opening latch, or the door jam latch? Take the door panel off, make sure that the window is up, and then you will have access to any of the latches. The door jam lock/opening latch will have some screws in it, 3 total, you can take those out and off for better access to the actual door lock mechanisms.

Apr 11, 2011 | 1994 Nissan Sentra 4-Door

1 Answer

2004 lexus gx470 rear door won't open...I can hear the lock click when I press the alarm key but the door will not open

Try opening door manually from inside, once open and make sure child safety switch (near lock mechanism isn't between on/off) They're known for jamming between settings. If that doesn't work then you'll have to remove inside door panel and access latch mechanism.

Mar 02, 2011 | 2004 Lexus GX 470

1 Answer

2006 corolla trunk won't open with the kay or the

the trunk lock mechanism might be jammed... if you have an access to the rear from the inside try pulling and moving some parts in the lock mechanism

Jul 15, 2009 | 1998 Toyota Corolla

1 Answer

Back hatch won't open with key or unlock button

will have to remove interior panel to gain access to locking mechanism and manually release latch. Something could be jammed in it and binding it or mechanism could have come loose inside or some linkage inside has broken. I had one with a beer can crushed between door and door jam. good luck

Jul 04, 2009 | 1999 Dodge Caravan

1 Answer

Lift gate wont open

OK, this minor collision may have shifted the actual clip and latch assembly. You may have to totally disassemble the latch assembly to release this lift gate.

Any kind of major or minor shifting of the lift gate lock latch assembly can cause misalignment that will jam this delicate precise locking mechanism.

Apr 23, 2009 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Active aeros on mitsu 3000gt

The Active aero on the front and rear are seperate and can fail seperately.
The rear often jams if the cables in the mechanism get stuck simply due to the grease drying up or there are two small relay switches in the mechanism that can fail so the electronics think give up trying to move and cause any damage.
The front air dam that lowers is driven off a simple motor and mechanical rod. the can jam or the motor can sieze.
both the front and rear mechanics can be removed relatively simply and cleaned which often solves the problem although it's not usually a permanent solution.
to test. turn the ignition on but keep the car stationary. press the aero switch all the way and the green light should come on and the air dam and tail should move. If the green light does not come on then I don't think you have a mechanical problem. When driving with the active aero turned on the air dam and tail will move above 45mph and reset when you go down below 25mph.
to access the front you need to remove the air dam itself from under the car. Two bolts at each end of the metal bar, two smaller bolts at each side of the air dam, two plastic clips in each wheel well and all the larger bolts directly on the bottom of the air dam. the motor assembly is on the passenger side. make sure it's not mechanically jammed or bent.
to access the reair lifft the tailgate, remove the large plastic cover trim. three nuts in the center section and two on each side. unplug the connector. close the tailgate and carefully lift the spoiler putting rags under the bolts so you don't scratch your paint. pull the connector grommet out of the while rather than pull the connector through the rubber grommet. the mechanics are simple but be careful to not change the alignment if you completey remove the motor drive unit. check the wiring, switches and that the mechanism moves freely.
testing for both front and rear can be done with the parts partially removed to look for mechanical issues.

Feb 25, 2009 | 1993 Mitsubishi 3000GT

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers


Level 3 Expert

85223 Answers


Level 2 Expert

104 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides