SOURCE: 1997 chervolet venture radio reset codes
I had the same problem with a 97 transport. Here is a couple solution to your locked radio problem. This is assuming you have the ACDelco radio original to the vehicle. One way is to allow the vehicle to warm for an hour. After warming the vehicle press either the 1/2 or 3/4 or 5/6 buttons together. In two on the sequences, a three digit code will come up. Write these codes down. I called the original seller of the vehicle, (if known) or a GM dealer. Speak with the parts or service department. They do not have the 4 digit code to unlock the stereo, though they can make a call to ACDelco and get the code. The other way is to take it to a dealer and have them erase the code, which is approx. 30-50 dollar depending on the service station. Hope this helps.
SOURCE: 2001 chevy venture lost key
You must get a new key from the dealer. Bring in the registration, and photo I.D. Then they will cut you a key. After that, try this procedure....
GM technicians on-line
SOURCE: Radio, Key auto door lock/opener, interior lights not working.
Most likely is a fuse. There is a fuse box at the end of the right side of the dash. Open front passenger door and there is a cover that says fuses on the end of dash. There is also a fuse box located under the hood at the right front of engine compartment. It should have a cover with a round knob in the middle of it .Unscrew the knob to remove cover.
SOURCE: wipers on 97 chevy venture won't go down when turned off.
The wipers appear to Malfunction by leaving the wipers up after turning
the wipers off. I found problem to be that corrosion sets in between the CAMS plates
that circle in an opposing fashion and does not let the wiper arms park
correctly. Be very careful with this mechanism if you have the cowling
off
TURN the KEY and WIPERS OFF and watch your fingers so you don't get them
caught.
WARNING if you leave the power on and try to move the arms This cam
mechanism springs to life and will try to self park the wipers on their
own so Turn the Power and Wipers Off.
SOLUTION:
1. With the ENGINE COLD, Spray a lubricant that FREE'S CORRODED PARTS
like WD-40 between the gap of the 2 CAM Plates and on Top of the plates,
or use some other automotive parts lubricant that free's corroded
parts(let it soak for 5 minutes).
2. Gently Try to manually move the arms back and forth a little bit so
that the spray works into the parts.
3. This may not be necessary but I had to do this the first time.
There is a notch in the top cam that has a STUD that locks the 2 CAMs
together. You can push on this STUD to unlock the cams by manually
moving the wipers(use a screw driver to push on the STUD and have a
friend gently move the wipers manually. Spray the area LIBERALLY with
with the Lubricant Spray and see if you can move the CAMS back and forth
and work the lubricant in.
Then with the wiper cover out of the way and all tools clear Try to
cycle the wipers HIGH and LOW, ON and OFF a few times it may stick the
first couple times with the wipers in the up position but I am confident
that the lubricant will work its way in and free these CAMS the way
they are supposed to.
Your wipers should self park after cycling them after 5-10times. This
should solve most of the problems with these
wipers and should be re-lubricated as needed. Clean up any extra
lubricant Put the wiper cover back on.
Hope this Helps
The CAM for the wipers that is about $85 at your local GM dealer.
It has instructions on how to install it correctly in the box the part
comes from. Good luck! and thenk you for using Fixya
SOURCE: I lost the key to my 1997 Chevy Venture, can I
u need to buy a replacement from the dealer otherwise a replacement key other than the original one wont be able to start ur car....
86 views
Usually answered in minutes!
×