Question about 2002 Chrysler PT Cruiser

1 Answer

2002 PT cruiser no lights,no crank, nothing when key is in ignition.battery full and cables tight

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

  • Expert
  • 73 Answers

I would start at the battery terminals. Loosen them and move them around to see if you get any lights, Even if the cables are tight they can still lose connection at times.

Beyond that you could follow the negative cable and see if it is tightly connected to the body of the car. Maybe flex the cables to see if there is any corrosion under the rubber coating.

If you have a volt meter test the ends of the battery cables (if possible) to at least verify you are getting power to the fuse box, or solenoid.

Posted on Jan 25, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Ron szarafinski

  • 217 Answers

SOURCE: 2001 pt cruiser limited won't crank

needs a battery but be careful cause sometimes a bad alternater will cause the battery to go bad

Posted on Jan 17, 2009

66 chrgr

mike loshbough

  • 1011 Answers

SOURCE: where is the crank sensor located on 2005 chrysler pt cruiser?

the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Posted on Jan 25, 2009

localwonder

Michael Masters

  • 6784 Answers

SOURCE: Change the thermostat on 2002 Chrysler PT Cruiser

Hi, i have put together a step by step guide that will help you with this replacement job. Make sure the vehicle is in a cool state before starting this job.


* Drain some coolant into a clean container until the coolant level is below the thermostat housing.
* Remove the upper radiator hose connection from the thermostat housing.
* Loosen the housing bolts and remove the housing.
* Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
* Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
* The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
* When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
* Install the gasket.
* Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
* When the engine has reached operating temperature make sure the thermostat opens.
* You should be able to see coolant circulating within the radiator.
* Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
* If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.

NOTE
When a paper gasket is used and the recess is in the thermostat housing, it is a good practice to position the thermostat into the recess and glue the gasket to hold it in place. If it falls out of its groove during installation, the outlet housing can be cracked or a coolant leak will result. Before tightening the water outlet housing, try to rock it back and forth to be sure it is flush. Housings are often cracked during this step.


9c06de2.jpg

Posted on Apr 30, 2009

GetMeOttaHere

  • 2926 Answers

SOURCE: I have a 2003 PT CRUISER MAN TRANS THE KEY WONT

Yes, the tumbler is worn, possibly from a heavy key chain or abnormally frequent stop/starts. Ther amy also be a bad connection in the switch connections itself, that may not require a whole new ignition switch.

Posted on Feb 14, 2010

cansmo

Reynaldo Andico

  • 2431 Answers

SOURCE: 2005 pt cruiser won't start won't crank, everything works

When you turn the key on the ASD relay should turn on the fuel pump and power the injector, Do this lets cheat the system go to the ASD rely open the cover expose the inside have some one turn the key on does the ASD make contact? If not turn the key on collpase the ASD so it make contact do you hear the fuel pump come on? Now try this just as how you iopen the ASD do the same to the starter relay. Put the car in gear e brake on someone in the vehicle in case the car start and you are in front of it and it runs you over so at least they step on the brakes. Key on ASD exposed as your collapse the starter relay does the ASD relay turn on? Here why if you can control all the relay from under the hood you will need a ignition switch (the eletrical part)

Posted on Feb 24, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 PT Cruiser. Only code is the neg was unhooked from battery recently. Car died pulling into parking lot. Cranks but won't start. Had a new transponder key made about a month ago. I'm thinking it may be...


Rather then guessing as to what the problem is , test . Is there a security light lit on the instrument cluster ? Does the vehicle have fuel pressure , spark ? Does the check engine light come on with the key in run position ?
No Start Diagnostic Basics EricTheCarGuy

Jan 20, 2018 | 2002 Chrysler PT Cruiser

1 Answer

Why does my 2002 PT Cruiser crank but not start?


Did u check for codes? On pt cruisers the odometer will read out a trouble code if the computer detects a problem with coil, spark etc. If ur checking to see if fuel pump comes on turn ignition on. You shpuld be able to hear fuel pump run for a few seconds and relays click on to start vehicle.
/uploads/images/2002-pt-cruiser-cracks-over-but-will-not-35076188-5-1.jpg

Feb 25, 2015 | 2002 Chrysler PT Cruiser

4 Answers

My car wont start but has Power


DOES YOUR CAR CRANKS OR IS COMPLETELY DEAD ONLY LIGHTS? IF IT CRANKS AND DOESN'T ENGINE RUN THEN IT IS EITHER THE ALARM ( IMMOBILIZER )SYSTEM ACTIVATED,OR THE IGNITION KEY FAILURE. IF YOU HAVE A SPARE IGNITION KEY TRY AGAIN ( THE KEY TO BE THE ONE WITH CHIP INSIDE ).IF IT IS COMPLETELY DEAD THEN YOU NEED THE ASSISTANCE OF A QUALIFIED PERSON TO DIS ACTIVATE THE ALARM AND CHECK ALSO YOUR SMART KEY AS WELL .

Sep 02, 2012 | 2002 Chrysler PT Cruiser

1 Answer

Ignition wont start the car when hot outside. U have to turn the key to the start position and hold for a few seconds or even crank or turn turn key the key past the start position to sometimes get it to...


My 2006 PT Cruiser has the same problem! When hot in the cab it won't start but after it is cool outside it starts up without missing a lick! When it is hot and you turn the key you get nothing but do have power to lights, radio, etc. weirdest thing ever and nobody knows why! We have had the ignition module replaced and have a new battery. This one has stumped everyone. Any suggestions folks?

Jul 24, 2010 | 2006 Chrysler PT Cruiser

2 Answers

My 2006 pt cruiser wont start, no lights or radio. nothing? when i turn key nothing happens inside or out


Check the battery terminals for corossion. Look for the chalky white powder which is a tell tale sign. Simply move the cable connectors back and forth a few times to loosen corossion and provide a better contact. Have you checked your fuses. I probably spelled corossion wrong, sorry.

Apr 25, 2010 | 2002 Chrysler PT Cruiser

1 Answer

2002 PT cruiser trying to start with no keys!


I would check your wire harness. The starter is close to where you would be working on the radiator. I have not had the pleasure to put one in but i know its a tight squeez in there.

Jul 22, 2009 | 2002 Chrysler PT Cruiser

2 Answers

2001 pt cruiser limited won't crank


needs a battery but be careful cause sometimes a bad alternater will cause the battery to go bad

Jan 16, 2009 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
2002 Chrysler PT Cruiser Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...