How do i program a keyless remote for my 2001 jeep grand cherokee laredo 4dr 6cy??

Keyless Remote Key Programming Procedure:

1. Insert first programmed key into ignition and turn ignition switch to ON for 5 seconds. ...
2. Turn ignition switch to OFF and remove key.
3. Insert second programmed key into ignition and turn ignition switch to ON. ...
4. Turn ignition switch to OFF and remove key.

More items...

Key Fob Keyless Entry Remote for 2008 Jeep Grand ...

..

See the link

https://www.google.com/search?q=program+keyless+remote+for+01+jeep+cherokee+grand

..

Transmission sticks in reverse- won't go into park. - JeepsUnlimited

www.jeepsunlimited.com/forums/showthread.php?...won-t-go-into-park
Jun 14, 2013 - 12 posts - ‎5 authors 2003 6 cyl 4x4 Grand Cherokee Laredo automatic- Occaionally, when shifting from REVERSE TO PARK, my Jeep will stay in reverse. Typically its ... '2001 WJ'4,0L'42RE'NV 242'380000 km'ECE Compliant' ??????????? ??? ...

2001 jeep grand Cherokee laredo - CarGurus

www.cargurus.com > Questions > Jeep > Grand Cherokee
CarGurusJan 27, 2014 - 2001 jeep grand Cherokee laredo - Just purchased a 2001 Jeep GrandCherokee Laredo and ... It starts in PARK sometimes and sometimes it won't and I have to start it in Neutral. ... Hatch shuts flush, but won't stay shut. help!

could be the key transponders are not working properly . you have to go to the dealer so they can perform a relearn.

Instructions

1. Programming the First Transmitter
   • 1

     Unlock all of the Jeep Grand Cherokee's doors and open the driver's side door. Keeping the door open, lock it using the manual lock on the door itself.
     

   • 2

     Put the manual key into the ignition and switch it to the "On" or "Run" position, whichever applicable, without starting the engine.
     

   • Sponsored Links
     

     • Remote Control Software

       Control any distant PC remotely. Test the Software now for Free!
       www.TeamViewer.com/Remote_Control

   • 3

     Point the remote at the receiver (located by the little bulb on the car ceiling) and hold down the "Lock" button for up to 5 seconds.
     

   • 4

     When the driver's side door unlocks, you know the remote has been programmed correctly. If you are only programming one remote, jump to the next step. If not, manually re-lock the driver's side door and repeat steps 5 and 6 using each remote you would like to program and then continue.
     

   • 5

     Turn the key to the "Off" position and turn the ignition on immediately. This must be done within 20 seconds of programming the last remote. You're finished!
     

Sponsored Links

Read more: How to Program the Remote on a 1996 Jeep Grand Cherokee ' eHow.com http://www.ehow.com/how_7433787_program-1996-jeep-grand-cherokee.html#ixzz2KdCc5PQq

someof them you cant you have to take it to the dealership

http://www.ehow.com/way_5447904_cherokee-keyless-remote-programming-instructions.html this site tell you how to program the remote for you

The dealer would have to do this. Or you can rent a DRBIII at techautority.com and it will guide you through the program.

remove the fuse

Open the drivers door and turn the key to the on position. Lock the doors with the switch on the door. After the doors lock point the transmitter to the little bulb on the ceiling. Press the LOCK button and hold it until the doors unlock.

Maybe this info can be help you...
http://autorepair.about.com/library/faqs/bl868f.htm