How do i bleed power steering pump peugheot 307 sw 2006 car petrol

Test charging circuit (usually for free at parts store). A battery getting drained can cause much of this. With car sitting still you could try removing fuses one at a time to see if there is an unusual draw.

first thing , mount the pump properly
if it is bely driven then the belt will not be driving properly to give power steering
if electrical driven then the earth for the pump will not be effective resulting in no power steering assistance
next take it to an accredited power steering shop for a proper diagnosis.

If it's the electrical motor type of pump, you must connect to a full scale scanner like Lexia 3 to get it reset.

hi.

i have never heard of a bleed nipple on power steering.

you just turn the wheele from full right lock to full left lock and back a few times and the system bleed itself.

if there is still a problem after doing this, then it suggests a fault in the compressor, or the rack itself.

Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.




*This originally came from abauto

YOU HAVE AIR IN THE POWER STEERING SYSTEM.YOU NEED TO BLEED POWER STEERING PUMP FIRST BEFORE DRIVING VECHICLE.CHECK POWER STEERING FLUID LEVEL ADD MORE POWER STEERING UNTIL REACH FULL COLD MARK..RAISE VECHICLE FRONT WHEELS OFF THE GROUND.START ENGINE LET IT IDLE WHILE TURNING STEERING WHEEL LEFT TO RIGHT NON STOP DONT LOCK OR STOP STEERING WHEEL KEEP TURNING IT SEVERAL TIMES CHECK POWER STEERING FLUID IF LOW ADD UNTIL YOU GET COLD MARK ON DIP STICK DONT OVER FILL POWER STEERING PUMP BLOW A SEAL.IF POWER STEERING FLUID LOOK TAN COLOR SYSTEM FULL OF AIR.TURN OFF IGNITION LET CAR SET FOR A WHILE CHECK FLUID LEVEL.IF STEERING WHEEL FEEL STIFF HARD TURNING DONT DRIVE CAR UNTIL YOU HAVE NORMAL STEERING.IF STILL HAVE AIR IN SYSTEM BLEED SYSTEM UNTIL AIR IS OUT.

its an electric pump on these vehicles and it has a thermal fuse ,by the sound of it i think this unit is playing up ,their about 600euros plus labout to change it

I have never heard of anybody bleeding the power steering pump, if you drained it or it just drained with the hoses removed, just fill it back up. It will pump itself through. The only noise out of that pump would be squealing from no fluid. I don't know why you had to remove that, The radiator should come out, straight up and clear just about everything. Hope this helps.

make sure you bleed it well lock steering left and right and hold to make sure all pipe are full pf fluid and top up power steering

check power steering fluid in engine bay