Trook intake off to inspect got it togeather runs very good but check engine wont clear code
You need to clear the code. I looked it up and this seems to be one way to clear a code once the fault has been fixed on a Chrysler T&C so it should work on the Sebring -
Checking and Removing Chrysler Engine Error Code WITHOUT USING SCANNER
SOURCE: ENGINE LIGHT ON SLIGHT LOSS OF POWER AND POSSIBLE RATTLE
p2004 (Intake Manifold Runner Control Stuck Open)You need to take a look at the IMRC actuators on the intake manifold. You can try using a screwdriver or other tool to move the actuators to see if one is stuck in the open position. Do not use your fingers to do this, because if one is open and decides to close it has a bit of force behind it and can injure you. If the IMRC is stuck open, it is usually due to deposits in the intake manifold. Repair involves removing the upper intake manifold and cleaning out any deposits in the IMRC plate area. I would try running some Techron Concentrate in 2 tanks of gas to see if it dissolves enough of the gunk on the plates to free up the stuck one. Certainly a lot cheaper than having to pull the intake manifold and cleaning the plates. Always run tier one gasoline like Shell or Chevron to reduce the buidup of deposits.
SOURCE: Check engine light came on
THERE IS A VALVE ON THE RIGHT SIDE OF THE INTAKE MANIFOLD THAT OPEN THE RUNNER.IT HAS A VACUUM LINE TO IT.FOR IT TO BE STUCK OPEN EITHER THE SOLENOID IS BAD,THE VACUUM LINE IS BAD OR THE RUNNER IS GUMMED UP WITH CARBON AND STUCK OPEN
SOURCE: I got a code P2004
what engine? So the guy running the test could'nt point it out to you? You need to find a shop that qualified to repair the car. its a valve on the intake manifold that opens and closes to help th engine produce the most power at low and high rpm. they get stuck. sometimes you can clean them.
SOURCE: 1998 ford windstar 3.8 with code p1538. Is this a
LOOKING IN CODE BOOK.POSSIBLE CAUSE TO YOUR PROBLEM THE IMRC COULD BE STUCK OPEN.OR THE IMRC ACTUATOR IS DAMAGED OR HAS FAILED.ALSO THE IMRC MONITOR SIGNAL CIRCUIT COULD BE SHORTED TO POWER GROUND OR SHORTED TO SIGNAL GROUND RETURN.
SOURCE: check engine light on..code short
P1004 - SHORT RUNNER VALVE CONTROL PERFORMANCE
Sound like something came loose. If you cannot find it you need to take it to the dealer so they can perform these diagnostics. Should be under warranty.
The engine performance and power output is enhanced through the use of the "short runner valve" (SRV) system. The SRV system allows the intake charge air to bypass the long intake manifold runners between the intake manifold plenum and the intake manifold interface to the cylinder heads by providing a shorter runner directly between the plenum and the cylinder head interface.
The SRV position is controlled by a pneumatic/spring actuator and electronic solenoid valve. When the solenoid is not energized (the "rest" position), the SRV is held in the closed position. When the solenoid is energized the SRV is moved and held in its opened position. There is a set of enable conditions including a minimum engine coolant and ambient temperature, SRV enable, and Powertrain Coordinator load enable condition. If any of these conditions are not met, then the SRV valve is de-energized (closed).
* When Monitored: With the engine run time above a calibrated value, battery voltage greater than 10.4 volts, ECT within a specific range, and the Short Runner Valve Assembly (SRV) control active.
* Set Condition: The Powertrain Control Module (PCM) compares the circuit feedback to a calibrated closed range, between 75% & 85% Pulse Width Modulated (PWM) duty cycle, when the circuit is de-energized or to a calibrated open range, between 35% & 55% PWM duty cycle, when the circuit is energized. If the value is determined to be out of the calibrated range in either the de-energized, greater than 85% duty cycle or less than 75% duty cycle, or energized, greater than 55% duty cycle or less than 35% duty cycle, state for more than a calibrated amount of time, this DTC will set.
Possible Causes
(F344) ASD RELAY OUTPUT CIRCUIT OPEN OR HIGH RESISTANCE
(K237) SHORT RUNNER VALVE (SRV) SIGNAL CIRCUIT SHORTED TO GROUND
(K237) SHORT RUNNER VALVE (SRV) SIGNAL CIRCUIT OPEN OR HIGH RESISTANCE
(K238) SHORT RUNNER VALVE (SRV) CONTROL CIRCUIT SHORTED TO GROUND
(K238) SHORT RUNNER VALVE (SRV) CONTROL CIRCUIT OPEN OR HIGH RESISTANCE SHORT RUNNER VALVE (SRV) ASSEMBLY
Hope this helps (remember to rate and comment this answer).
890 views
Usually answered in minutes!
×