Replacing exterior door handle on 1998 camry

It removes just like the older style handles with one exception. You must remove the electrical clip/wire that attaches to it while still in the door. It has 2 black clips top/bottom for the harness, one white clip for the actual connector to come off handle (removes toward center of vehicle. After this is off and of course the part behind the moveable handle then the moveable handle will shift backwards and out while swinging rear away from door.

No the door handle is easily replaceable. you do have to remove the door panel and roll the window all the way up. 2 10mm nuts inside the door cavity and one bolt on the door jam near the lock mechanism. These handles are made of plastic and degrade and break easily after 3 or 4 years. Every toyota owner has to deal with this at some point. I also recommend buying the new handles on ebay as opposed to the dealer. The aftermarket handles are better quality than the original and MUCH cheaper. They are ALWAYS available on ebay.

Pull the vertical rods not the horizonal rods.

Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

1. Visually inspect the following:
   Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible

1. Turn ignition key to position II.
2. Motor door glass to fully raised position.
3. Turn ignition key to position O.
4. Disconnect the negative battery cable.
5. Remove door casing for access.
6. Remove door water shedder.
7. Position PVC secondary water shedder for access.
8. Slacken and remove the door glass rear runner lower securing screws.
9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
10. Slacken and remove the upper securing screw and move the runner away from the glass.
11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
12. Slacken and remove the three latch assembly securing screws and position latch for access.
13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
15. Remove lock motor assembly from door.
16. To install, reverse removal procedure.
    
    
    

    Fig. Removing door lock actuator
    

Sedan

1. Remove the door window glass
2. Detach the interior door handle.
3. Detach the actuator remote cable from the interior door handle.
4. Remove the interior door handle.
5. Detach the door window glass run.
6. Remove the exterior door handle retaining screws.
7. Remove the front door actuator retaining screws.
8. Reposition the front door actuator and exterior handle.
9. Remove the front door actuator and exterior handle.
10. Disconnect the front door actuator remote cable.
11. Detach the door lock cylinder connecting rod (1).
12. Detach the exterior door handle connecting rod (2).
13. Remove the front door actuator (3).
14. To install, reverse removal procedure.
    
    
    

    Fig. Removing door lock motor-Sedan
    

Hope this helps.

HAVE TO REMOVE THE DOOR PANEL REMOVE ALL EXTERIOR OR VISIBLE FASTENERS AND MOST DOOR PANELS HAVE PLASTIC CLIPS ALSO SECURING THEM TO THE DOOR FRAME.ALSO ANY ELECTRICAL WIRING INTERFERING WITH PANEL REMOVAL. THEN ACCESS THE TWO NUTS/BOLTS ATTACHING IT THE THE DOOR FRAME. THEN REMOVE THE RODS ATTACHED TO THE HANDLE GOING TO THE LATCH/LOCKING MECHANISM AND REVERSE THIS PROCEDURE FOR INSTALL.

Remove the interior door panel, then the lock mechanism which should then reveal the screws or nuts that hold the exterior handle in place.

Two 10mm bolts, or nuts, hold the handle on from inside the door. dont forget to remove actuating rod from old handle. probably clip is broke also.

My 96 Camry LE has 9 attachments that are visible. Some have plastic caps covering the screws; others do not. There are screws at the door handle, at the forward portion(with covers) when the door is open and the back edge (small covers). As I recall, there are several friction type fasteners around the perimiter of the panel that can be removed by prying carefully away from the metal portion of the door to free up the trim panel. Once these are loose, the trim around the inside door release handle (the one you pull to open the door) can be pryed in a backward motion. Then the entire panel can be removed by pulling upward and backward at the same time (it easier to do this with the window down). Then it is a matter of disconnecting the wires attached to the various controls for the electric windows and door locks to free up the panel itself. There is probably a plastic skin covering the metal portion of the door. Carefully pull that away to expose the inner workings of the door latch mechanisim. The rest of the procedure should become easy to figure out. I have not removed the exterior door handle itself; but it is a simple mechanism as I recall. Best of luck to you.
Timmy P.

ok. first u remove the door panel(s), with the window rolled up, u will be able to see the back side of the exterior door handle. there will be three bolts, they are size 10metric. there is also a rod attached to the handle held in place by a plastic clip, remove the rod, then remove the three bolts. from the outside remove the exterior door handle being careful not to scratch painted surface. Repeat for the other door(s). Repeat this for installation.

remove door panel.. inside door you will see a rod going to the handle..on the end is a clip ..push the clip up off the rod .slide the rod out..remove 2 ..13mm nuts from handle ..remove handle