How do I remove the front seats - 1995 Cadillac DeVille

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.

Head Restraints Each front seat is equipped with dual-post design front seat back head restraint (611A08). The front seat back head restraint is installed as follows:

• It travels on dual posts which have notches to engage a spring-loaded catch in the guide.
• The front seat back spring assembly retains the front seat head rest guide rod sleeve (610A16).

• The front seat back head restraint is adjustable from its normal position to a raised position of approximately 25 mm (1 inch).
• Pull up on the front seat back head restraint to raise it. Pushing down will return it to its normal position.

----------------------------------------------------------------------------------------------

Removal

1. Unscrew front seat head rest guide rod retainers (610A18).
   

1. Pull up on front seat back head restraint (611A08). Compress foam in area of front seat head rest guide rod sleeves (610A16).
   

1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
   

Installation

1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
   

1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves.
   

1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
   

1. Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves.
   

1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve.
   
   Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint.
   

seat frame base is held to floor with four bolts, one in each corner.  Begin by moving seat to the full forward position, remove the two rear seat frame bolts, they may be covered by carpet and plastic trim.  Them move seat to full rear position and remove both front frame bolts, the seat will now be free to remove.  Keep me posted

2 bolts in the front and two in the rear of each seat, 10 minute job, disconnect wiring under seat, take care not to break the locks on the connectors for the power seats.

1. Remove front seat.
2. Remove adjuster cover. A
3. Slide floor anchor cover.
4. Remove floor anchor bolt. B
5. Remove shoulder anchor bolt. C
6. Remove front and rear kicking plate, then remove center pillar upper and lower garnish.
7. Disconnect seat belt pre-tensioner connector.
8. Remove the screw securing seat belt pre-tensioner retractor, then remove seat belt and seat belt pre-tensioner retractor.
9. Remove bolts securing seat belt adjuster, then remove seat belt adjuster. Reverse procedure to install.J

Requires the use of a t-50 torx socket & you'll remove four bolts. Viola, the seat is loose & all models will have electrical connections to disconnect.

Check the fuse

There are 4 bolts holding the seat to the floor. 2 in front and 2 in rear. You will need 14mm socket and ratchet or wrench. You will also have to unplug some connectors under the seat, before you take it out of the car.

One of two ways. There may be two tabs at the bottom front of the seat bottom. Pull those out toward the front of the car, and then firmly pull up on the front of the seat bottom. Or, if there are no tabs, then just pull up very firmly on the front of the seat bottom.

You can not remove the far back seat, only the middle one. But you can slide it all the way foward. I have had my van for two years and just learned how to do it today from my husband. Below the rear are two levers. A and B. Make sure the back of the seat is in the upright position and then pull on Levee A. At the same time, lift of the bottom of the seat. It will go up and fold together making a V with the back of the seat. Then pull lever B and slide seat forward.