SOURCE: how many bolts hold a starter on in a Mazda 626 1995?
there are 3 bolts holding it to the transmission bell housing, see picture below.
SOURCE: Mazda protege rear strut replacement 02
they're underneath the plastic deck cover in the back, where the speakers are. -just a few plastic fasteners and the wire connector for the rear light, and it'll pop right off. -just did it myself this weekend
SOURCE: What are the torque specs of the head bolts of a
step 1 17-19 ft/lb
step 2 90 degrees
step 3 additional 90 degrees
engine uses Torque To Yield head bolts
New head bolts must be used when cylinder head is replaced or re-installed
stockam auto
If you need further help, reach me via phone at https://www.6ya.com/expert/dennis_f849d3d6a68c6430
SOURCE: do i need to remove camshaft bolt to remove
1 Locate the crankshaft pulley on your vehicle. This is usually on the driver's side, but may be on the passenger's side if your timing belt is located on the passenger's side. Place the end of the tire wrench over the lug nuts of the appropriate wheel of your vehicle and turn the wrench about 45 degrees. 2 Put your emergency brake on. Then use the floor jack to jack up the vehicle's front jack point (an extension of the frame).3 Put the jack stands under the frame of the vehicle. Then, lower the vehicle onto the jack stands. 4 Continue to loosen and remove the lug nuts, and pull the wheel off.5 Remove the plastic rivets that hold the splash guard in place in the wheel well. To do this, you need to wedge the screwdriver in between the rivets and the splash guard and pry them out.6 Locate the crankshaft pulley. It will be right behind the splash guard you just removed.7 Remove the crankshaft bolt using the crankshaft bolt remover tool. Place the tool over the crank pulley bolt in the center of the pulley. This device prevents the pulley from rotating while you loosen the bolt.8 Place the socket end of the impact wrench over the crankshaft bolt remover tool. Set the impact rench to turn counterclockwise and turn on your air compressor. Wait until the compressor is fully charged. Then, work the bolt loose. It may take a while as this bolt normally requires in excess of 800 ft lbs of torque to remove.9 Attach the arms of the crankshaft pulley removal tool over the pulley and tighten the tool to the pulley using the tool's supplied bolts. Continue to tighten the tool using the bolts until the crankshaft pulley is pulled off the crankshaft.
SOURCE: 97 Mazda Protege dies while driving down the highway and will not start.
check fuel pressur, filter and fuel pump...sounds like it isnt getting fuel
The Mazda Protege Cheap Oil Pan that we sell could be mounted easily at the bottom of the crankcase of the vehicle. For fast and helpful information on a Mazda Protege OEM Oil Pan give us a call toll-free! We guarantee a secured server, so you can rest assure your information is kept safe when you place a Mazda Protege Oil Pan order! You can rest assure that you will always be treated with the best care and service with your Mazda Protege Replacement Oil Pan purchase! Excessive tightening of Mazda Protege Oil Pans can cause the gasket to get smashed, so put an extra care during installation. Ordering Mazda Protege Drain Oil Pan online is fast and simple, however, giving us a call toll free can have greater benefits because we can provide expert advice and suggest additional parts that may be needed that you are not aware of! We have proficient sales specialists who are ready to answer your queries regarding Mazda Protege Aftermarket Oil Pan. Did you know that our online catalog is available at all hours to take and process your Mazda Protege New Oil Pan order? That's right! The Mazda Protege Discount Oil Pan is considered as one of the major components of the cooling system.order it to .......racepages.com/parts/oil_pan/mazda/protege.html
158 views
Usually answered in minutes!
×