Peugeot 3008 2012 1.6 H D I. Can someone please confirm torque setting for 36mm nut, when replacing rear discs that have wheel bearing attached?

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

Rear Suspension - Rear Wheel Bearing Fusion 2002.75 (06/2002-)

-Removal and Installation

Special Tool(s)

Installer, Differential Bearing
205-062

Installer, Input Shaft Seal
307-210 (17-041)


General Equipment
Soft faced hammerWooden block

Removal

CAUTION: The brake drum and hub assembly removal in this procedure is for installing a new wheel bearing, not for access to brake system components.

-All vehicles

Remove the dust cap.
Remove the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

-Vehicles with rear drum brakes
Release the parking brake.
Remove the brake drum and hub assembly.
Remove and discard the wheel hub retaining nut.


-Vehicles with rear disc brakes
Remove the brake disc.
For additional information, refer to in this section.

Remove the wheel hub.
Remove and discard the wheel hub retaining nut.


-All vehicles

Remove and discard the wheel speed sensor ring (brake disc shown).
Remove the circlip (brake disc shown).
Using the special tool, remove and discard the wheel bearing (brake disc shown).

-Installation

-All vehicles

CAUTION: Support the wheel hub assembly on the wheel mounting face and not on the wheel nut studs.

Using the special tool, install the new wheel bearing (brake disc shown).

Install the circlip (brake disc shown).

CAUTIONS:

Make sure the wheel speed sensor ring is not knocked, damaged and kept free from metal fragments.

Protect the face of the wheel speed sensor ring with a non-ferrous flat block to prevent damage.

Make sure the wheel hub or brake drum is adequately supported and do not allow it to rest on the wheel studs..

Make sure the wheel speed sensor ring is pressed on slowly and squarely until fully seated.

Do not exceed a maximum load of 10 kN.

Using the special tool, install a new wheel speed sensor ring (brake disc shown).

Vehicles with rear drum brakes

CAUTIONS:

Avoid impact on the wheel speed sensor ring.

Make sure the wheel speed sensor ring is clean.

Avoid any contact between the wheel speed sensor ring and a magnetic surface.

Rotate the wheel hub assembly 10 times counter-clockwise when tightening the wheel hub retaining nut to prevent damage to the wheel bearing.

NOTE: Install a new wheel hub retaining nut.

Install the brake drum and hub assembly.
Apply the parking brake.

-Vehicles with rear disc brakes


CAUTIONS:

Avoid impact on the wheel speed sensor ring.

Make sure the wheel speed sensor ring is clean.

Avoid any contact between the wheel speed sensor ring and a magnetic surface.

Rotate the wheel hub assembly 10 times counter-clockwise when tightening the wheel hub retaining nut to prevent damage to the wheel bearing.

NOTE: Install a new wheel hub retaining nut.

Install the wheel hub retaining nut.
Install the brake disc.
For additional information, refer to in this section.


-All vehicles
Install the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

NOTE: If the dust cap is damaged a new dust cap must be installed.

Using a soft faced hammer and a wooden block, install the dust cap.


There is no real torque settings for the rear wheels, except to say, do not over tighten or you will stretch the lugs and the will loosen over time.

WHEEL BEARING LARGE HUB NUT TORQUE 232 FT LBS.

4-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake shoes
     
   • Rear halfshaft nut and loosen the halfshaft from the hub
     
   • Wheel hub and place it in a vise
     
   • Inner wheel bearing race from the hub
     
   • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
     
   • Parking brake cable from the steering knuckle
     
   • Brake line from the wheel cylinder and support the knuckle
     
   • Lower shock absorber nut
     
   • Lower ball joint by holding the ball joint stud
     
   • Upper ball joint
     
   • Coil spring while noting the location of the insulator
     
   • Steering knuckle cam
     
   • Steering knuckle
     
   • Snapring and press out the outer wheel bearing race from the knuckle
     

     Rear hub and bearing
     Click to Enlarge

To install:

1. Install or connect the following:
   
   • New wheel bearing into the steering knuckle
     
   • Snapring to the knuckle
     
   • Wheel hub
     
   • Steering knuckle cam and hand tighten the bolt
     
   • Coil spring
     
   • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
     
   • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
     
   • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
     
   • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
     
   • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
     
   • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
     
   • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
     
   • Brake shoes
     
   • Rear wheel
     
   • Negative battery cable
     
2. Fill and bleed the brake system.
   
3. Check and adjust the wheel alignment as needed.
   

2-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake drum
     
   • Wheel hub nut
     
   • Wheel hub
     
   • Inner wheel bearing race from the hub
     
   • Snapring
     
   • Wheel bearing outer race from the knuckle
     

     Rear hub and bearing
     Click to Enlarge

     Rear hub removal
     

     Inner wheel bearing removal-rear hub/bearing
     

     Rear wheel bearing removal-2wd
     

     Rear wheel bearing removal-4wd
     

To install:
Install or connect the following:

• Wheel bearing in to the knuckle
  
• Snapring
  
• Wheel hub into the wheel bearing
  
• Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  
• Brake drum
  
• Rear wheel
  
• Negative battery cable
  

  Rear wheel bearing installation
  
  hope this helps if so send testimonial comment or even any other questions you have
  

remove this items in this order(rear disc):
-remove rear wheel(the side you are replace)(19mm socket)
-remove brake caliper with cailper bracket(14mm socket)
-remove brake disc
-remove metal cover hub/bearing assembly with flathead screwdriver
-remove 36mm nut behind metal cover.
-pull hub/bearing assembly out.
note:sometime the inner side of bearing stay on knuckle and you have to pry it out pry bar. check old bearing vs new bearing and you'll see the different. Don't reuse any parts of the old bearing.
-install new hub/bearing

Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical)

1. Release parking brake.
2. Remove rear wheel assembly.
3. Remove rear wheel speed sensor from carrier.
4. Dismount brake caliper and support with mechanic's wire.
5. Remove brake disc.
6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical)
   
   
7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
8. Remove carrier.
9. Remove stakes and remove flange nut.
10. Support bearing outer race flange and press rear axle hub out.
11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.

To Install:
Hub bearing assembly (Typical)

1. Apply thin coat of grease to bearing contact surface and hub.
2. Using and appropriate tool, press bearing into hub. CAUTION
   Do not press against outer race of wheel bearing.
   
3. Install flange nut and stake nut until it meets concave portion of spindle.
4. Install carrier.
5. Use an appropriate tool to press tone wheel.
6. Install hub/bearing assembly with rounded portion of outer race facing up.
7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
8. Measure wheel bearing starting torque with a spring balance or equivalent device.
   • Starting torque should measure 15.9 in lb (1.8 Nm) or less
9. Install brake disc.
10. Mount brake caliper.
11. Install rear wheel speed sensor to carrier.
12. Install rear wheel assembly.

Tightening torque for the hub nut is 200Nm and the road wheels are 85Nm

NOTE: The rear wheel bearings are remowned on these cars for sticking to the stub axle quite badly, and often have to be forced off using a slide hammer on the drum, it is quite common to end up damaging the wheel bearing, so be prepared to replace this as well in this event

drum brakes you remove rear wheel- speed sensor-grease cap-flange nut-outer bearing-brake drum-inner grease seal-inner bearing-drive the bearing races out of the drum hub.to install -install the inner and outer bearing races.apply grease to the bearings and hub cavity.then you install the inner bearing -inner grease seal-brake drum-outer bearing-flange nut torque it to 159 to 192 ft lbs. THE REAR DISC BRAKE WHEEL BEARINGS-you have to remove rear wheel -wheel speed sensor-brake caliper and rotor-rear axle hub bolts-tone the wheel with tool 09445-21000-carrier assembly-nut after unstaking it-press out the rear axle hub-remove the bearing inner race with tool 09445-21000-remove the bushings from the carrier with tools 09453-33000b and 09545-21100.to install -press in the bushings to the carrier with tools 09453-33000b and 09545-21100- press in the bearings to the hub with tool 09221-21000.tighten the flange nut to meet the concave portion of the spindle-press in the tone wheel with tool 09221-21000-torque the nut to 191 ft lbs -install the hub and bearing assembly to the backing plate and torque the bolts to 88 ft lbs-install the brake caliper and rotor.install the wheel speed sensor if equipped.install the rear wheel.TO BUY THE TOOLS TO DO THE JOB.LOOK UP KENT MOORE TOOLS ON INTERNET.

here is how to replace it on a 2 wheel drive please do not forget to rate and comment about your experience today. 2-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake drum
     
   • Wheel hub nut
     
   • Wheel hub
     
   • Inner wheel bearing race from the hub
     
   • Snapring
     
   • Wheel bearing outer race from the knuckle
     
3. 
   

To install:

1. Install or connect the following:
   
   • Wheel bearing in to the knuckle
     
   • Snapring
     
   • Wheel hub into the wheel bearing
     
   • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
     
   • Brake drum
     
   • Rear wheel
     
   • Negative battery cable
     

You will need several tools to replace the bearing besides a socket set of metric and standard sizes to remove the wheel and brake caliper. A 36mm socket (may be rented at some auto parts stores) An Impact Wrench for the 36mm socket (air or electric should work) A torque wrench (IMPORTANT!)- the 3 rear bearing bolts (12mm?) need to be torqued properly or else they will fail and cause the wheel to separate, i believe they need to be at 75 ft/lbs. Please check. Do not attempt to do this yourself unless you have the proper tools and know how to use them.  I recommend getting at least the Haynes manual that the stores have or buying the Dealers Service Manual (expensive but thorough and usually available on ebay!)