Question about 2005 Dodge Caravan

Open Question

I need the torque specs for the time cover for a 2005 dodge caravan 3.3 v6

Posted by on


6 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017



SOURCE: coolant

check the rear heater lines on the right side(passenger side) of the van. there is a rubber hose that was leaking on mine. I found it after the dealer said nothing was wrong.
It did not cost anything for repair as they had a service note on it.


Posted on Jun 16, 2008



  • 85223 Answers

SOURCE: i need torque specs for 94 rodeo

flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Posted on Feb 14, 2009


  • 134 Answers

SOURCE: need the torque spec on the rear diff. cover bolts - 2005 F-150

just tighten them down you dont need to torque them its not nessary.

Posted on Nov 04, 2009


  • 149 Answers

SOURCE: I need the torque specs for the connecting rod cap

Step #1 40lbs PLUS Step#2 1/4 turn 90 degrees.....this is for 3.3 & 3.8

Posted on Jan 19, 2010


  • 1 Answer


How do I know how to put the torque converte on the same holes like it was be fore to the fly wheel

Posted on Apr 23, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter

Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

I need the 1993 dodge caravan 3.0 v6 sylinder head bolt torque speks

The correct torque for the head bolts on a 3.0 v6 caravan motor is 70 Ft-lbs. (as stated in my Haynes Service manual)

Dec 19, 2010 | 1993 Dodge Caravan

1 Answer

Torque sequence and settings for head bolts on 3.3 dodge caravan motor?

torque and sequence spec on 2005 caravan 3.3l cylinder head bolts

Jan 17, 2010 | 1998 Dodge Caravan

1 Answer

I need the torque specs for the connecting rod cap bolts for a 2005 dodge grand caravan

Step #1 40lbs PLUS Step#2 1/4 turn 90 degrees.....this is for 3.3 & 3.8

Nov 07, 2009 | 2005 Dodge Grand Caravan

1 Answer

Need to the torque for the oil pan for a 2005 dodge caravan with a 2.4 engine

Hello rkz3: The correct torque specs for the oil pan is 105 inch pounds. Should you need further help just ask.Thak you for using FixYa. Please rate the information as it helps a lot. Thank you again Roger

Apr 16, 2009 | 2005 Dodge Caravan

1 Answer

2005 Grand Caravan Brake Job

Better late than never, right?
According to Haynes 30013: "Dodge Carvan, Chrysler Voyager & Town and Country, 2003 through 2006" Repair Manual:
Caliper Guide Pins or Guide Pin Bolts - 26 Ft-lbs

Nov 20, 2008 | 2005 Dodge Caravan

Not finding what you are looking for?
2005 Dodge Caravan Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides