My dome light and mirror courtesy lights stay on when the door is closed in my 1994 Chevy Lumina euro, I also noticed that my break light blows up , where do I start to look for that short ?

If the dome lights in your 2009 Cadillac CTS are not turning off, it can be a frustrating issue. Here are some steps to diagnose and potentially fix the problem:
1. **Manually Turn Off the Dome Lights:**
- In most vehicles, including the Cadillac CTS, there's typically a manual switch on or near the dome light itself. Ensure this switch is in the "Off" position.
2. **Check for Open Doors:**
- Make sure all doors, including the trunk and the hood, are completely closed. Sometimes, a door ajar can prevent the dome lights from turning off.
3. **Interior Light Dimmer Control:**
- Check the position of the interior light dimmer control, which is usually located on the headlight switch or dashboard. If it's turned all the way up, it may keep the dome lights on. Adjust it to the lowest setting.
4. **Ignition Switch:**
- Ensure the ignition switch is in the "Off" position. Sometimes, if the ignition switch is left in the "Accessory" position, the dome lights may stay on.
5. **Faulty Door Switches:**
- Each door usually has a door switch that signals the lights to turn on when a door is opened and off when it's closed. One of these switches may be malfunctioning. You can try manually pressing and releasing each door switch to see if the lights respond.
6. **Battery Disconnect and Reconnect:**
- If the above steps don't work, you can disconnect the vehicle's battery for a few minutes and then reconnect it. This can sometimes reset the electrical system and resolve the issue.
7. **Consult the Owner's Manual:**
- Refer to your Cadillac CTS owner's manual for specific information about the dome light controls and troubleshooting tips.
8. **Professional Diagnosis:**
- If the issue persists, it may be related to a more complex electrical problem. In this case, it's advisable to consult a professional mechanic or an auto-electrician to diagnose and repair the problem.
It's important to be patient and methodical when troubleshooting this issue, as it can have various causes. If you're not comfortable working on the electrical system of your vehicle, seeking professional help is a wise choice to avoid further complications.

Interior Lamps
The interior lighting consist of the following 2 groups. This first group includes lamps that may not be dimmed.
• The cargo lamp
• The dome lamps
• The reading lamps
• The vanity mirror lamps
Courtesy Lamps
The courtesy lamps include the reading lamps, cargo lamp, and dome lamps. The cargo lamp and dome lamps may be manually turned ON or OFF by placing the interior lamp switch in the ON or OFF position. When the driver places the dome lamp defeat switch in the OFF position, these courtesy lamps will be disabled. If a door is opened, the courtesy lamps illuminate. After all the doors have been closed, the courtesy lamps will remain illuminated approximately 15 seconds after the last door closes. The courtesy lamps will also turn ON prior to any door being opened and will remain illuminated approximately 40 seconds when the driver removes the ignition key. The body control module (BCM) will immediately turn OFF the courtesy lamps if a door lock command is received with all of the doors closed, or if the ignition switch is turned to either the ON or RUN position.


These lights ?

Vanity Mirror Lamps
The inadvertent power courtesy lamps supply voltage circuit of the body control module (BCM) provides battery positive voltage to each vanity mirror lamp. When the vanity mirror cover on the sunshade is opened, a switch closes to provide a ground circuit and the vanity lamp illuminates.
Battery Rundown Protection/Inadvertent Power
The body control module (BCM) inadvertent power courtesy lamps supply voltage circuit provides battery positive voltage to all of the interior reading lamps and both visor vanity mirror lamps. In the event that any of these lamps were to remain illuminated for a period of more than 20 minutes with the ignition switch in the OFF position, the BCM will deactivate the inadvertent power courtesy lamps supply voltage circuit to prevent a total battery discharge condition. Only when the ignition switch is cycled back to the RUN position will the BCM reset the internal timer and reactivate the inadvertent power courtesy lamps supply voltage circuit.
The BCM also utilizes the inadvertent power courtesy lamps supply voltage circuit as a courtesy lamp request signal circuit when none of the lamps in the circuit are illuminated. When a lamp switch is activated, the BCM receives the request for lamp illumination and switches to supplying voltage to the inadvertent power courtesy lamps supply voltage circuit.

Check fuses under the hood on driver side

all the lights above the dash do not work ?????? DOME light's ??? No light's come on when you open the door or any door ? Wouldn't think all the door ajar switches bad at one time .
Interior Lamps
The interior lamps consists of two groups, lamps that can not be dimmed and lamps that can be dimmed. This first group consists of lamps that may not be dimmed. This Includes those lamps that may be manually turned on by placing the interior lamp switch to the DOME position, or by opening a door or a compartment:
• Auxiliary dome lamp (SEO, RPO 6C7)
• Dome lamp
• instrument panel (I/P) compartment lamp
• Inside rear view mirror lamps
• I/P courtesy lamps
• Reading lamps
• Rear compartment courtesy lamp
• Sunshade vanity mirror lamps
Battery positive voltage is applied at all times to the DIC/RKE fuse and to the switched side of the BATT RUNDOWN PROTECTION relay in the right I/P junction block. The DIC/RKE fuse supplies battery positive voltage to the coil side of the BATT RUNDOWN PROTECTION relay. When the ignition is turned to the ON position, the body control module (BCM) provides a ground to the Inadvertent relay control circuit. This energizes the BATT RUNDOWN PROTECTION relay and applies battery positive voltage to I/P BRP fuse and to the TRK/ROOF/BRP fuse. Battery positive voltage is applied from the I/P BRP fuse to the I/P courtesy lamps, I/P compartment lamp and to the I/P compartment feed circuit to the BCM. Battery positive voltage is also applied from the TRK/ROOF/BRP fuse to the:

If the BCM receives a door lock or unlock input signal, the BCM will activate the BATT RUNDOWN PROTECTION relay, which provides battery positive voltage to all interior courtesy lamps. When any door is opened, the door jam switch contacts close and the BCM receives a door-open input signal. The BCM then applies a ground to the theater dimming ground control circuit illuminating the courtesy and dome lamps.
After all the doors are closed, the courtesy lamps remain illuminated for approximately 40 seconds. The courtesy lamps will also turn on and remain illuminated for approximately 15 seconds after the ignition key is removed, prior to any door being opened.
When the headlamp switch is placed in the DOME position, the BCM receives a ground signal. The BCM then applies a ground to the theater dimming ground control circuit. This illuminates the dome and roof rail lamps.
The courtesy lamps will normally turn off using the theater dimming feature. The BCM provides a pulse width modulated ground to all courtesy/reading, dome, and inside rear view mirror lamps for the theater dimming feature. The BCM will immediately turn off the courtesy lamps if a door lock command is received with all the doors closed, or if the ignition switch is turned to either the ON or RUN position.
The BCM activates the interior lighting output 15 seconds after receiving the class 2 message "Airbags Deployed" from the sensing and diagnostic module (SDM). The interior lamps remain activated for 25 minutes.

The door ajar switch is part of the lock actuator inside the door !

Glad you solved it.

first unplug both mirrors one at a time to see if they are causing this, also test if with the doors closed also could be door switches if not the most common place to look is in the driver door jam , wires usually chafe and short out.

To temporarily solve the light problem, I taped a washer to the inside of the door where the door hits the plunger on the light switch. A permanent solution would be to drill a hole in the door at this spot and put a self taping screw in that will trigger the switch sooner. I figured out the reason the dome light stayed on is due to the courtesy light timer and the lights would have eventually gone off.

do they squeak all the time or just on cold take off , thats why i dont use semi mettalic junk pads i use ceramics, as far as the abs could of have a bad sensor at the wheel, i also found that a lose battery cable at the battery will cause this to. But as far as the anti lock light concerned u got regualr brakeing so neeed to panic.

Don't think you have a door ajar switch problem , more then like the lighting control module is the culprit . Does the door ajar light on the instrument cluster stay lit ?
The interior lighting can be separated into two distinct modes of operation: the courtesy lighting and the demand lighting. The lighting control module (LCM) controls all of the interior lighting in the vehicle, as described in the following text.
The front dome lamps, rear reading lamps, and instrument panel courtesy lamps, can be illuminated either by opening any of the vehicle doors (courtesy lamp function) or by depressing the headlamp switch (demand lamp function).
When any door is open, the door ajar switch grounds an input to the LCM which then sends power to the courtesy lamps. The voltage sent to the courtesy lamps gradually increases from 0 volts to 12 volts within 500 ms (± 50 ms), to achieve the theater lighting effect. When the door(s) are closed the door ajar switch(es) break(s) the ground to the LCM input which then gradually reduces the power from 12 volts to 0 volts within 5 seconds. (± .5 second).
When the headlamp switch is depressed it grounds an input to the LCM which in turn sends 12 volts to the front dome lamps, rear reading lamps, and instrument panel courtesy lamps. When the headlamp switch is depressed a second time, it breaks the ground to the LCM input which then ceases to send power to the front dome lamps, rear reading lamps, and instrument panel courtesy lamps.

The battery saver will disrupt power to the courtesy lamps after 10 minutes, the demand lamps after 30 minutes, and the headlamps after 10 minutes. Turning the ignition switch to the RUN or ACC position will terminate the battery saver feature by disabling the interrupt timers and reinstate power to the lamps.
Do you know what DTC'S are ? diagnostic trouble codes !
LCM Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1322 Driver Door Ajar Circuit Short to Ground LCM Go To Pinpoint Test F . B1442 Door Handle Switch Circuit Failure LCM Go To Pinpoint Test G . B1445 Door Handle Switch Circuit Short to Ground LCM Go To Pinpoint Test G . B1563 Door Ajar Circuit Failure LCM Go To Pinpoint Test C . B1566 Door Ajar Circuit Short to Ground LCM Go To Pinpoint Test H . B1685 Lamp Dome Input Circuit Failure LCM Go To Pinpoint Test I . B1687 Lamp Dome Input Circuit Short to Battery LCM Go To Pinpoint Test I . - All Other DTCs LCM REFER to Section 419-10 .

PINPOINT TEST C: THE COURTESY LAMPS STAY ON CONTINUOUSLY CONDITIONS DETAILS/RESULTS/ACTIONS C1 CHECK THE SYSTEM OPERATION Open and close each door, making sure that each door is completely closed.

• Are the courtesy lamps still illuminated after the 25 second time-out period?

Yes GO to C2 .

No The system is operating correctly. C2 TEST DOME LAMP SWITCH Depress the dome lamp switch.

• Are the courtesy lamps still illuminated?

Yes DEPRESS the dome lamp switch a second time. GO to C3 .

No The system is operating correctly. C3 CHECK THE LIGHTING CONTROL MODULE
LCM C2145a

• Are the courtesy lamps still illuminated?

Yes REPAIR circuit 53 (BK/LB). REPEAT the self-test. CLEAR the DTCs.

No INSTALL a new LCM. REFER to Section 419-10 . REPEAT the self-test. CLEAR the DTCs.

Are you sure that the thumb wheel switch beside the headlamp switch is not turned all the way up until it clicks?
If it is staying on for 10 minutes this means that the smart junction box is seeing a demand for the interior lights from something like a door ajar switch or the thumb wheel. If it sees that the igntion is in the off position it will turn the lights off after 10 minutes to conserve battery power.
Normal operation is:
The interior lighting delay feature provides temporary illumination of the courtesy lamps after the doors are opened and then closed. The interior lighting delay feature keeps the courtesy lamps on for a period of 25 seconds after all the doors are closed. If during the 25-second delay time the SJB detects that the ignition has been switched out of off, or if the vehicle is locked using the RKE, the courtesy lamp illumination is discontinued