No fule pressure no iggnition spark no injector pulse
SOURCE: no injector pulse
hello sir,
absence of ground pulse means there is some kind of shorting circuit in your control circuit.
which can make the ground pulse to get shorted there itself preventing it to reach the circuit properly.
thank you
don't forget to rate the solution
good day
SOURCE: 1991 oldsmobile cutlass supreme
Check for fuses/power/ground to the engine computer (or injector drive computer) whatever the case is.
Spark, fuel pump, and starter all are independant of the fuel injection computer.
Either the computer itself has gone bad, or it is not receiving power or ground, or wiring to the injectors might be bad...
SOURCE: 1991 suzuki samurai want start
Check ECM (engine computer) located under glove box. Injector circuit output probably dead. Replace ECM. Go to Searchparts.com for best price.
SOURCE: 1985 corvette no pulse to injectors
Very important that if you are not savvy of working on your Vette ...you would be better off - taking your car to a dealership for repairs on your trouble codes. However if you feel that you want to, First locate your car's alcl this component is located just below the instrument panel and to the left of the center console. Remove the plastic cover the first two slots to your right are the A & B slots.
The A slot is the diagnostic slot and the B slot is the ground slot. Insert the computer key into these slots if you do not have a computer key, a paper clip or wire jumper clip will do, (with the engine off) this is very important...now only put the ignition key to on ( not start !!!) the check engine light will display a code 12 which is one flash followed by two flashes. This code will be flashed three times ..followed by the trouble code stored in your car's computer.
What ever the code is it will be flashed three times. Have a paper and pencil ready and write down the code.
Code #12: Normal No Codes.
Code #13: Open Oxygen Sensor Circuit.
Code #14: Coolant Sensor Circuit Low.
Code #15: Coolant Sensor Circuit High.
Code #21: Throttle Position Sensor High.
Code #22: Throttle Position Sensor Low.
Code #23: Manifold Air Temperature Circuit High.
Code #24: Vehicle Speed Sensor.
Code #25: Manifold Air Temperature Circuit Low.
Code #32: EGR System Failure.
Code #33: Mass Air Flow Sensor High.
Code #34: Mass Air Flow Sensor Low.
Code #36: Mas Air Flow Sensor Burn-Off Function Fault.
Code #41: Cylinder Select Error.
Code #42: Electronic Spark Timing.
Code #43: Electronic Spark Control.
Code #44: Lean Exhaust indication.
Code #45: Rich Exhaust Indication.
Code #46: Vehicle Anti Theft Fault.
Code #51: Faulty Mem-Cal.
Code #52: Fuel Calpak Missing.
Code #52(1990-91 Corvette Only): Engine Oil Temperature Sensor Low.
Code #53: System Over Voltage.
Code #54: Fuel Pump Circuit Low Voltage.
Code #55: Defective ECM.
Code #62: Engine Oil Temperature Sensor Circuit High.
Please remember that if you have the computer key installed in the alcl and you start the engine (you will ruin the engine's computer) only put the ignition to on (not to start).
If you should get a check engine soon display.. you can use the above procedure and codes to buy the right part or at the very least to keep from getting taken for a ride and be made to pay hight prices for some inexpensive module that you could have installed yourself.
If your engine displays a trouble code ... your engine will go into limp mode ..it will still run but very poorly. You might be able to reset the computer if it will not start (just to get home) by disconnecting both battery cables and re-installing them ...this is not recommended ..but if you are stranded it might help unitl you get your car home or to a repair shop..good luck.
Good luck and hope this helps.
SOURCE: 1989 Ford Ranger 2.3l. Won't
if by no injector pulse you mean no electrical signal to injector, no that wont do it, that would be related to a bad ECM
I would first check to see if you have good fuel pressure; if not the fuel filter and/or pump would be suspect.
If you have good fuel pressure but no signal to the injector(s) the ECM is probably the problem
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c
658 views
Usually answered in minutes!
Does the PCM have power and ground ?
×