Cars & Trucks Logo

Related Topics:

J
James Patton Posted on Jun 08, 2018

I have a 08 dodge nitro 4.0.V6 it cranks for a long time be for it starts, it does not matter if it is hot or cold but runs fine.

5 Related Answers

Anonymous

  • 6487 Answers
  • Posted on Jul 26, 2008

SOURCE: hard to start when hot

This can be a problem with your starter so better check the starter or have it replace...

Hope that helps........

Ad

Anonymous

  • 393 Answers
  • Posted on Nov 17, 2008

SOURCE: Hard starting hot or cold. Battery and starter are fine.

check fuel pump relay/should run pump for two sec when key is turned on. try turning key on but dont crank did pump hum/if it did look towards leaky fuel inj./faulty pressure reg. poss clogged fuel filt.

Jonah Oneal

  • 14092 Answers
  • Posted on Apr 27, 2009

SOURCE: 2003 Dodge Ram 3500 Diesel hot and cold start issues without plug

your glow plugs not working or glow plug relay or controller not working.

Anonymous

  • 1 Answer
  • Posted on Jan 31, 2010

SOURCE: 1996 Ford Ranger won't start

I had the same problem , and if you read your book, it could be the fuel pump shut off switch, mine was bad and went from on to off position, its usually under the passenger side of the dash, look underneath at the "top" of the carpet, and you'll see a little red switch, check to see if the thing is plugged in , if it is , check to see if the switch is all the way down. i had to get a new one , sombody must have kicked mine and made it broken, but i got a new one and it worked fine

Anonymous

  • 1970 Answers
  • Posted on Jul 09, 2010

SOURCE: TOWNCAR COLD AND HOT ENGINE PROBLEMS

mcdevito75 here, Sounds like something in the ignition system, a bad ignition module or coils, Have your repair shop take a look at these items.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2008 Dodge Nitro blows cold air constantly but coolant fine.

If both the coolant hoses are hot then the coolant is passing through the heater core. You probably have an actuator or blend door that is not working. It may be restricted by commanding it to work. A scanner could help you find out the problem.
0helpful
1answer

2010 Dodge Nitro 3.7l stopped running. What do I need to do now?

It is a problem in your wiring system. You will have to start from a point and check all the wires all the way to your dashboard . Most commonly its a live wire that is touching the boddy . You can conect a diagnose computer and it will pin point the problem most of the time
0helpful
1answer

Knock sensor 08 dodge nitro

Look at youtube

Knock sensor location on Dodge grand Caravan 3.6
1helpful
1answer

08 dodge nitro blows hot air on passenger side but cold air out the drivers side!! Any answers



NOTE: LHD model shown. RHD model similar. All vehicles are equipped with a common heater, ventilation and air conditioning (HVAC) housing assembly (1). The heating-A/C system combines A/C, heating, and ventilating capabilities in a single HVAC housing mounted within the passenger compartment behind the instrument panel. The HVAC housing assembly includes:
  1. Mode-air doors (2)
  2. A/C evaporator (3)
  3. Recirculation door actuator (4)
  4. Air inlet housing (5)
  5. Recirculation-air door (6)
  6. Blower motor (7)
  7. Blower motor resistor (8)
  8. Heater core (9)
  9. Air distribution housing (10)
  10. Blend-air door (11)
  11. Blend door actuator (12
  12. Floor distribution ducts (13)
  13. Mode door actuator (14)
0helpful
1answer

08 nitro blows hot air out the passenger side but cold out the drivers side! Was told half the heater core was plugged!! Could that even be possible?

If core was blocked by leaves, etc, I suppose this might be possible, but more likely there is a flapper door not working correctly, due to vacuum leak or bad actuator.
0helpful
1answer

T10 blazer hard to start when cold,easy to start when hot

4.3L V6 CPI - center port fuel injection . you need 62 psi .When cold give it a shot of carb.cleaner or starting fluid ! does it start then ?

415-455 kPa (60-66 psi
1helpful
1answer

My 1997 Dodge Avenger's engine won't start

Try cam and/or crank sensor. If crank to cam timing isn't detected properly it'll crank all day but won't start. I had similar problem on my 2.5L V6 Avenger....drove home fine, no engine light, next morning it cranked, but wouldn't start. The crank sensor was faulty.
1helpful
2answers

1995 dodge ram won't start when warm

Yes the crank sensor can cause this problem, they go open when hot.
Not finding what you are looking for?

626 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...