In replacing a throttle body to a 2005 Chrysler 300 Limited could you explain the correct procedure for relearning

The Navigator is totally run by electronics. The only way to diagnose is with professional grade scan tool computer. It takes about 30 minutes. The throttle body has a relearn / reset procedure.

https://www.google.com/search?q=mobile+auto+electrician+near+me

https://www.google.com/search?q=2005+lincoln+navigator+throttle+body+relearn

..

This explains the issue

https://www.google.com/search?q=2005+chrysler+300+lightning+bolt+on+dash


you can also try resetting the security system as well


https://www.google.com/search?q=2005+chrysler+300+security+reset

..

You must calibrate and relearn the throttle body position to your computer. Google: Ford Vehicles: Electronic Throttle Body Calibration Procedure.

P2110 Throttle Actuator Control System Forced Limited RPM https://www.autocodes.com/p2101_chrysler.html

here you go
Wont idle down after throttle body cleaning 06 trailblazer throttle body relearn procedure Yahoo Video Search Results

most of the time when you clean throttle body needs to do a relearn
GM Truck Electronic Throttle Body ETB Relearn Procedure GM throttle body relearn procedure Ricks Free Auto Repair Advice

https://www.google.com/?gws_rd=ssl#q=computer+relearn+process+for+2007+Chrysler+300

2005 Chrysler 300 2.7l Throttle Body Control Warning Light ...

www.cargurus.com > Questions > Chrysler > 300

CarGurusAug 7, 2014 - 2005 Chrysler 300 2.7L throttle body Control warning light or "RED ...bolt starts flashing and the car gets stuck in limp mode or second gear.Missing: p

PCM/TCM Software Updates Will Address Shifting Problems ...

repairpal.com > Problems > Chrysler > 300

Chrysler 300 PCM/TCM Software Updates Will Address Shifting Problems. ... If you experience rough shift and/or shuddering during gear shifting, software ... Car would not go over 20 mph and check engine light along with ABS/BAP light ... Once he put the new battery in the car ran fine for a while and the problems all cam ...Missing: p

ECM with bad connection, causing engine to stall - 2005 ...

? 1:08
https://www.youtube.com/watch?v=IgLe0t5may8
Oct 23, 2011 - Uploaded by SignedOnAsJoe
Check NHTSA chrysler extended the warranty on fuel tanks. ...Any one knows how can I put a used ecm in my 2005 300 do I need to buy new ... How to view fault codes Chyrsler 300 HTWL - Duration: 1:22. by Leo P 28,908 views ... Rough Run, Stumble or Stall, Check Engine Light-How To Check Vehicle ...Missing: blink

The throttle bodies on most newer cars are not adjustable for its idle speed. If the Check Engine Light is on, go to the nearest auto parts store and get them to pull the error codes from your car's computer. Post the codes back here and we can give you a better answer to your question

There is a technical service bulletin that may apply to your problem the no. is 09-8-9

ISSUE: Some 2005-2009 Escape Hybrid and 2006-2009 Mariner Hybrid vehicles may exhibit an intermittent Red Triangle On and Stop Safely Now message displayed on the message center accompanied by a sudden RPM loss/no start symptom with a diagnostic trouble code (DTC) P1A0C. Vehicles may exhibit this symptom on the first start of the morning or after an extended idle. The symptom will clear on the next key cycle.
ACTION: Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE For vehicles outside the new vehicle limited warranty, if diagnostics lead to replacing the throttle body you may use this procedure to clean the throttle body as an alternative to replacing it. This procedure is not covered by the new vehicle limited warranty. NOTE: THIS CLEANING PROCEDURE CAN ONLY BE USED ON NON-COATED THROTTLE BODIES. Refer to Workshop Manual, Section 303-04C Removal and Installation - Throttle Body.

1. Remove the throttle body.
2. With the throttle body positioned to the side, open the throttle plate.
3. Using Motorcraft® Choke and Linkage Cleaner or equivalent, spray the throttle body plate and bore.
4. Using a suitable (nylon) brush, clean the edges of the throttle plate and the mating surface of the throttle bore to remove all carbon build up.
5. Reapply Motorcraft® Choke and Linkage Cleaner or equivalent and wipe clean with a lint-free cloth.
6. Remove old throttle body gasket and discard. Install a new throttle body gasket.
7. Install the throttle body.

PART NUMBER PART NAME PM-14 Motorcraft® Choke and Linkage Cleaner