Toyota Corolla 1nz torque setting, main bearing, big end , cylinder head and camshaft bearing

read the manual,
no country told at all
below is N.America only see, is this clear ?



https://eautorepair.net/Marketing/Default.asp

cylinder head bolts
stage1-20NM
stage2-40NM
stage3-60NM

MAIN BEARINGS
stage1-30NM
stage2-60NM

BIG END BEARINGS
stage1-25NM
stage2-49NM

FLYWHEEL
78NM

Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :

• Use new bolts and tighten as follows:
  • 1,4/1,6 = 35 Nm + 30° + 15°
  • 1,8/2,0 = 65 Nm + 30° + 15°
• "Pot"-type flywheel = 65 Nm + 30° + 15°
• Tighten drive plate to 60 Nm.

Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :

• Tighten nut in three stages:
  1. 130 Nm
  2. Slacken off
  3. 20 Nm + 80°-90°.

Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

1997 Toyota Prado 5VZ-FE
Cylinder head bolts:
Tighten the cylinder head bolts in criss cross manner inside out, in four stages as under:
Stage 1. Torque the bolts up to 17 Nm.
Stage 2. 34 Nm.
Stage 3. Rotate all the bolts 90 degrees.
Stage 4. Finally rotate all the bolts further 90 degrees.

Main Bearings:
Tighten the main bearing bolts in two stages, as under:
Stage 1. 61 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Big end bearings:
Tighten the big end bolt of connecting rods in two stages as under:
Stage 1. 25 Nm.
Stage 2. Rotate the bolts further 90 degrees.

ays as well as response to this question UVB the radiation. But it always recommended Vita Luminance while using safe sunscreen as per your skin sensitivity. Zinc oxide sunscreens are constructed from metallic zinc that recently been oxidised. It absorbs the UV rays and hence protects your skin from acquiring it contact with sun sun light.



http://utrimcleanseblog.com/vita-luminance/ Vita Luminance


Injection Free Solution For Youthful Skin

Torque:
- Connecting rod (big ends). Tighten bolts in several steps. 1st stage 29 NM, 2nd stage, rotate further 90 degrees
- Main cap bolts (crank shaft). Tighten bolts in several steps. 1st stage 44 NM. 2nd stage, further tighten 90 degrees.

This site has all the torque specs you should need make sure this is the correct engine.

http://www.davidfarmerstuff.com/C6Z06-Torque.pdf

hi big end bearings are two stage, 25nm leave ten mins, then 49nm cylinder head bolts three stages 20nm leave ten mins, 40nm leave ten mins then 60nm check after 5,000miles hope this helps

whats the torque setting for big end bearing bolt and cylinder head bolt for toyota corolla 12 valve 2E,1990.