Question about 1997 Isuzu Rodeo

1 Answer

How to replace front cv shafts ?

Do the shafts pop out of diff ? or does diff cover and pin need to be removed to be able to access snap rings ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Isuzu Master
  • 459 Answers

Remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Posted on Aug 06, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I04 Lincoln Navigator. Front differential pass seal leak. remove the drive shaft and unbolt the flange. the inner flange does not have a bolt to access the seal and bearing. How is the seal accessed?


If I understand you correctly the drive shaft you took out is actually a CV axle. The inner axle shaft goes into the diff. That is held in with a snap ring in the diff. It might not come out easy, sometimes they do, use a pry bar to pop it out. Be careful not to break or damage the aluminum housing. There have been times where I had to use a strong air hammer to beat on the back side of that flange to get the axle shaft out... It's sort of like taking a CV axle out of a front wheel drive car.

Oct 27, 2017 | Lincoln Cars & Trucks

2 Answers

How do you pull a 1979 gmc jimmy 4x4 rear right axle


QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.

Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)



see this vdio

Apr 01, 2015 | GMC Jimmy Cars & Trucks

1 Answer

Need to remove the divers side axle shaft on my 2003 dodge ram 1500... Have everything off and the front diff cover off already not sure how to get the shaft to come out of the differential... I'm aware...


Sometimes even with all of the clips off you have to use an axle puller to "knock" it out. The bearing is in the housing pretty tight. One of the national autoparts staore that starts with letter A has a nice rental/loaner program for that.

Good luck!

May 25, 2014 | Cars & Trucks

1 Answer

Front and back berring dissassembly of differential 2001 dodge 1500


For the rear diff., remove the driveshaft, brake drums, diff. cover, remove pinion flange nut, move diff carrier to access side gear retainer bolt and remove bolt, slide side gear pin out and push axles in to remove axle retainers and remove axels. Mark carrier bearing retainers, spin bearing retainers to loosen carrier for removal. Remove carrier, remove pinion out of diff case, then r&r bearings. Any shims should be replaced in their original location for depth and pinion to ring contact.

Feb 05, 2011 | 2001 Dodge Ram 2500 Truck

2 Answers

I have 99 zr2 pickup and where the cv shaft slides into the differential is leaking.i have the cv shaft off and i have to pull the old seal off but the axle shaft is in the way, do i have to drop the hole...


Open the bell. Take off the rear gear cover. U will loose all the fluid if any still in it so only remove some of the bolts loosen leave like 3 in around the bottom loosen them out a oil pan under the cover pry the cover off the diff leaving the 3 bolts to keep the cover from just popping off it will also help slow the rush of fluid. Once the fluid is drained remove the bolts and cover. On the inside u will se side gears. Have a helper push the axle shaft inward then u will see there is a C clip holding the axle carfully pry off the clip. Only do one side at a time. ... Then slide the shaft out where ur helper is. .. remove and replace the leaking seal. Then clean the axle. And u have to be easy sliding it in. Some times when the axle shaft is slide in u hit the end of the tube push the axle down toward the ground with variety of pressure as u push in this is tricky. But it will pop in. Then replace the clip and gentle have a helper try and pull back on the shaft. This sets the clip from falling out. Clean the bell area and scrap the old gasket off both sides if u have no replacement gasket get high heat black rtv silcone apply it to the cover or diff face and reverse the steps to install fill it with fluid and road test all this can be seen on youtube under inner axle seal repair. Good luck.

Feb 10, 2018 | 1999 Chevrolet S-10 Pickup

1 Answer

Tried removing the front drive shaft from transfer case. It won't come off, could there be something holding it from inside the transfer case?


Unbolt it from the front diff and then pull it out of the front of the transfer case. There will be a small snap ring inside that will offer up resistance, but it does slide out with some help, use your pry bar between the shield and the t-case to "pop" the spline past the snap ring inside. the first one i did i was kinda leary of prying on this too, but it was what was required just pull on the front drive shaft with one hand, and pry behind the shield with the other it'll feel like it's not going anywhere, but watch out, it'll just "pop" and be out. Be careful!! Good Luck!

Mar 09, 2010 | 2005 Chevrolet Silverado

1 Answer

Rear axle oil seals leaking, book shows to remove pinion shaft lock bolt so as to remove pinion shaft, but i find no bolt to remove, is this shaft press fit or did they foget to install bolt?


TAKE TIRES OFF, REMOVE DIFF. COVER, ON 3rd MEMBER THERE A PIN ABOUT 11/2" DIA. THAT GOSE RIGHT THOUGH THE 3rd MEMBER CLOSE TO ONE OF THE ENDS OF THAT PIN OPOSIT OF RING GEAR THERES AN 8mm SMALL HEAD BOLT ( TURN RING GEAR TO CHECK OTHER END OF PIN ) REMOVE BOLT PUSH AXLE IN REMOVE HORSE SHOES CLIP IN 3rd MEMBER SLIDE AXLE OUT.

Nov 10, 2009 | 2003 Chevrolet Silverado 2500HD

2 Answers

How do you change rear axle seal in a chevy pickup


To change the rear seal, yo will need to raise and support the rear of the vehicle. Remove the wheels and drums or rotors (depending on drum or disc brakes.) Remove the rear differential cover bolts and the cover (have a drain pan under the differential) You will likely need to turn the driveshaft so the center pin bolt is acessible at the back or the differential. This is a 5/16" (or 8mm) bolt that is on the right (passenger) side of the differential carrier assembly. I recommend a new bolt be installed here on reassembly. Once the retaining bolt is out, slide the center pin out enough to allow the axle shafts to be pushed in toward the center of the diff. to remove the "C" clips that retain the axle shafts in the carrier assembly. Be careful if you happen to pull the center pin all the way out not to allow the carrier assembly (has the ring gear mounted on it) to turn, as this can rotate the spider gears out of alignment causing a headache on reassembly. With the "C" clip removed the axle shaft can be pulled out of the diff. Inspect the bearing area of the shaft for rust, pitting, or scoring. Remove the old seal and carefully install the new one. Reverse proceedures to install. Take care to note the "C" clips and center pin bolt are properly reinstalled. Fill with 2.5 to 3 quarts of rear axle grease for you vehicle.
good luck.

Oct 25, 2009 | 2000 Chevrolet Silverado

1 Answer

Need picture on how to break down 1998 blazer **** slip / ratched rear


jack rear end pull wheels & tires brake drums or rotors put truck in neutral pull cover turn drv shaft till you see a 5/16 bolt head or 8mm on right hand side pull bolt out a pin should fall out if not get a hammer & hitt diff in axle once or twice (not the gear the case that gear is attached) remove fallen out pin, push axle shafts in remove a horse shoe retainer from both sides, now pull both axle shafts out, remove the four bolts with caps (warning don't mix caps up) get big pry bar pop diff case out..go to auto zone web sight the have basic help manuals

Sep 09, 2009 | 1998 Chevrolet Blazer

1 Answer

How do I get the clutch to release from the transmission on a evo


All 1996 Model Year and newer vehicles
equipped with manual transaxles except Accents
, which have the "push" type clutch system. SERVICE PROCEDURE:
  • Drain the transaxle gear oil.
  • The reference photo to the right shows the clutch related components as viewed from outside the transaxle case.
75c260f.jpg Loosen the release lever nut and washer
Separate the release lever by removing the snap pin and clevis pin.
Separate the release lever from the fork shaft.
Loosen the bolts attached to the release cylinder and separate the release cylinder from the transaxle assembly (no need to open the clutch hydraulic system).
  • Remove the transaxle assembly after removing each bolt attached to the engine assembly.
  • Remove the clutch cover assembly. The release bearing is still attached.
To separate the release bearing from the clutch cover, rotate the release bearing to gain access to the bearing snap ring.

5affa6e.jpg

Mar 28, 2009 | 2003 Hyundai Santa Fe

Not finding what you are looking for?
1997 Isuzu Rodeo Logo

923 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

459 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...