How do i replace freeze plugs on a nissan altima 1996

francisco navarro

• 241 Answers
• Posted on May 15, 2008

SOURCE: Replacing a starter for a 1999 Altima

1. Disconnect battery ground cable.
2. Disconnect starter wiring from starter.
3. Remove starter retaining bolts and the starter.
4. Reverse procedure to install.

SOURCE: Need to replace freeze plug on engine

both... put some gasket sealer on the outer sides of the new freeze plug before you tap it in.  

SOURCE: 1993 nissan altima running rough...also misses sometime when idli

spark plugs, air filter and fuel filter.

SOURCE: Car shakes violently when car is in gear and brake

If car shakes violently when brakes are pressed, this is probably the rotors.

If car will not shift gears, you better get your wallet out, because it is probably your transmission. An engine diagnosis will not pick this up.

ZJ Limited

• 17989 Answers
• Posted on Apr 05, 2010

SOURCE: How do you remove a 1999 Nissan Altima starter?

Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation

1. Remove or disconnect the following:
   Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle



Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle



Fig. Starter location and mounting detail-3.5L Maxima

1. Install or connect the following:
   Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable
   

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable
   

1. Before servicing the vehicle, refer to the Precautions section.
   
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
   

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable
   

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable
   

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
   

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle
   
   
   Fig. Starter location and mounting detail-3.5L engine