Question about 1995 Jeep Grand Cherokee

Open Question

95 JEEP GRAND CHEROKEE 5.2 ENG PO118 ERROR CODE I REPLACED SENSOR STILL CAN'T RESET CODE

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 2 Answers

SOURCE: Jeep Hesitates. P0303 code

Check the cylinders Commpression. over 115 psi is good, 120 psi is normal.

Posted on Sep 17, 2008

Ad

Anonymous

  • 41 Answers

SOURCE: engine code 95 jeep grand cherokee lerado

12 is a battery disconnect within the last 50 start cycles and 55 means the end of the diagnostic cycle.  Basically the computer found nothing wrong. The 12 code may seem incorrect if you haven't disconnected the battery recently, but from my experience the 12 code shows up almost all the time regardless.

Posted on Dec 16, 2008

Anonymous

  • 10 Answers

SOURCE: location of crankshaft position sensor Jeep grand cherokee 1997

left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Posted on Jun 13, 2009

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: where to replace coolant temp sensor for 1998 grand jeep cherokee

Check this image...

b33c4b0.png

...in the Section ZJ-Secc-8D-Ignition-Systems (page 5, fig. 10 and 11).

Good luck.



Posted on Sep 07, 2009

Anonymous

  • 1985 Answers

SOURCE: how to replace the Battery Temperature Sensor

it is located under the battery in the battery tray.

Posted on Jan 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need help with a code 12 for. 95 grand Cherokee orvis 5.2l. In need of some help. I know what the code says, but don't understand what it means.


A code 12 just means that memory to the controller has been cleared within 50-100 engine starts, which can occur whenever the battery terminals are disconnected, battery completely dies, etc. Nothing to worry about really, and it is NOT related to the thread that you found.
http://www.jeepforum.com/forum/f11/jeep-cherokee-help-error-code-12-a-1172243/

The codes you found indicate there are no stored trouble codes: Code 12 means that the battery or the computer power lead was disconnected sometime during the last 50 operating cycles. This is not an indication of a problem. Code 55 means that there are no other stored codes in the computer.
http://answers.edmunds.com/question-95-5-2L-Jeep-Grand-Cherokee-Ltd-code-12-What-should-I-do-93723.aspx

http://www.bing.com/search?q=error+code+12+jeep+grand+Cherokee&qs=n&form=QBRE&pq=error+code+12+jeep+grand+cherokee&sc=0-33&sp=-1&sk=&cvid=F34E2340514C41A7B7139E3671F6D25D

Jun 12, 2016 | Cars & Trucks

1 Answer

What is an error Code P1296 Jeep CHEROKEE 2000


It is a 'under 5 volts' error to the map sensor.

Nov 17, 2013 | 2000 Jeep Grand Cherokee

1 Answer

What are codes 12 and 21 for 95 jeep grand cherokee 4wd


Check this:
Code 12 - Direct battery input to PCM was disconnected within the last 50 key-on cycles.

Code 21 - Neither rich nor lean condition detected from the oxygen sensor input or O2 (Oxygen) sensor input voltage maintained above the normal operating range.

Code 55 - End test.

Just need to check or replace the O2 sensor, is the only fail that your computer found there. Is need other details, dont dude in contact us.

Good luck.

Oct 03, 2011 | 1995 Jeep Grand Cherokee

2 Answers

01 Jeep grand cherokee laredo won't start. No fire is going to engine. Changed spark plugs but didn't help at all


you might want to check you cam shaft sensor amd also there is a different sensor under the distutor i had to replace both of these on my 95 jeep grand cherokee laredo

Dec 04, 2010 | 2001 Jeep Grand Cherokee

1 Answer

1999 jeep grand cherokee. p0152, p0141, p0161


All 3 codes are point to the o2 sensor
the one you want to replace is on the exaust manifold looks like a spark plug with a wire sticking out of it un plug the sensor and it turns to the left to get off install the new one and plug the new sensor in
Thanks

Jul 14, 2010 | 1999 Jeep Grand Cherokee

1 Answer

Eng.lightis on code#p0031.


Have you diconnected the battery for 20 min to reset the puter?

Sep 11, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Code 53


Hello yeremya1776,

For Jeep Grand Cherokee, 1991-95 models:

Code 53 - Internal Controller Failure - Internal engine controller fault condition detected during self test

Hope this helps.

Remember: Good things come to those who Rate!!

Mike

Aug 06, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...