It's a manual transmission and as soon as I shift up, that's when it's hesitates. Check engine began flashing today. Any suggestions?
SOURCE: hesitation acceleration
have you checked the fuel injector? if enough fuel is not getting through when accelerating it could "choke" causing the hesitation
SOURCE: hesitation during acceleration
could be the type of plug you are using.I was told only to use ngk plugs.I recently put bosch plugs in my mazda 3 and the check engine light came on and it started missfiring.
SOURCE: engine hesitating during acceleration
Ok, there are many issues here that you will need to inspect. I recommend changing the fuel filter and pump as well. this will fix the hesitation. the intake and exhaust manifold gaskets will need to be replaced as well. this will stop the backfiring.
I also recommend checking and running a teat on the PCV valve and inspect the PCV hose as well. it could have a leak or a small crack on it.
Check the air filter and change if needed. this will help with acceleration issues as well. Next, i would run a check on all plugs and the complete wire set as well. change if needed.
Inspect the injectors for leaks and lose wires. make sure they are in good condition. replace any injectors that isn't firing properly.
Ok, there are some sensors that you will need to check as well. i will list them below.
SENSOR CHECK LIST--
1. Check the O2 sensors for worn wires.
2. Check the MAFS(Mas Air Flow Sensors) Check for Damaged, Loose, or Faulty Mass Air Flow Sensor or Circuit.
3. Check the Air Cleaner Temperature Sensor. this sensor could be damaged ro have loose wires. check accordingly.
4. Check the Throttle Position Sensor. this device could be connected wrong or it may be faulty as well. replace if needed.
Be sure and inspect all the above and repair any problem spot you ruin across during your inspection.
Please rate and god bless:)
SOURCE: 1989 Cavalier Z24 3.1 rough idle and hesitation
I had the same problem with my Z when i had it. But it worked when i just left the little hose off of the EGR valve.
SOURCE: Poor performance, hesitation, sluggish and shaking
Those are cylinder misfire codes. PO300 is random misfires (meaning 1+ cylinders misfired) and the other 2 codes are for cylinder #1 and 2. Did you change the ignition coils yet on 1 and 2?
Do you let the tank go to empty before refueling a lot?
ENGINE HESITATES WHILE ACCELERATION
LOSS OF ACCELERATION
It
can be fuel pressure issue or it's the problem with accelerator pedal or its
clogged filters causing there.
There
are many other possibilities. I suggest you to go through the list of help
links mentioned below, these will help you to confirm where the actual fault
lies: -------
-----------
http://technoanswers.blogspot.in/2012/02/loss-of-acceleration.html
---------
http://howtobyme.blogspot.in/2012/02/headlights-flickering-and-car-hesitates.html
--------
http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-accelerator-cable.html
-------------
http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-accelerator-pump.html
--------
http://whatisbyme.blogspot.in/2012/05/2000-toyota-avalon-engine-lean-codes.html
---------
http://whatisbyme.blogspot.in/2012/05/2004-toyota-avensis-acceleration-and.html
---------
http://technoanswers.blogspot.in/2012/04/wheel-hop-under-hard-acceleration.html
--------
http://technoanswers.blogspot.in/2012/02/2009-chevy-impala-accelerator-pedal.html
---------
http://technoanswers.blogspot.in/2012/02/nissan-pathfinder-stalls-and-bucks-on.html
--------
http://repairhelpcenter.blogspot.com/2012/01/acceleration-lag-problem.html
-------------
These details will help.
Thanks.
2,302 views
Usually answered in minutes!
×