There's this website www.reliable-store.com
They have books on ALL vehicles.
it covers
wiring diagrams, electrical diagrams, fuse diagram, torque specs, PCV, error codes, fault codes, service info, repair info, parts info, owner's/service/repair/parts/maintenance manuals etc everything totally..
I have 1987 toyota 4runner model and I keep servicing and when needed repair it on my own. worth it !!!
SOURCE: failsafe engine mode
The failsafe mode can appear following numerous faults being detected - some faults can be momentary and register but not cause a problem. These are normally reset by just turning ignition off/on. get the fault code memory read at a garage and this may give you a clue as to a possible problem developing. Failsafe mode will give you reduced engine performance but will allow you to drive for normally some distance. If a serious problem developes your car message centre will tell you to shut off the engine or it will shut it down.
good luck.
SOURCE: program 2004 mercury mountainer garage opener
Verify the hand-held transmitter is operative.
Prepare for programming the universal transmitter by erasing all three channels (hold down the two outside buttons until the red light begins to flash [20-30 seconds]). Release both buttons.
Select one of the three universal transmitter channels to be programmed by pressing the desired button
Hold the end of the hand-held transmitter 25-51 mm (1-2 in) from the front surface of the universal transmitter so that the red light can still be seen
Use both hands to press the hand-held transmitter button and the desired button on the universal transmitter. Do not release either button.
Hold down both buttons until the red light on the universal transmitter flashes, first slowly and then rapidly. Release both buttons when the rapid flashing begins. The universal transmitter has successfully learned the new frequency signal and can be used in place of the hand-held transmitter(s).
If the hand-held transmitter appears to program the universal transmitter but does not open the garage door, the garage door opener may have a code protected or rolling code feature.
To operate, simply press the appropriate button on the universal transmitter. The red light is on while the signal is being transmitted.
IF THE GARAGE OPENER HAS ROLLING CODES---
program as above then------
Train the garage door opener receiver to recognize the universal transmitter.
Remove the cover panel from the garage door opener receiver.
Locate the training button on the garage door opener receiver. Location and color of the button may vary by garage door opener manufacturer. Refer to the garage door opener instruction manual or owner literature.
Press the training button on the garage door opener receiver for 1-2 seconds.
Press the programmed universal transmitter button for as long as the universal transmitter red light flashes (1-2 seconds). Release the button and re-press the button to confirm that the universal transmitter is trained to the receiver.
The garage door opener should recognize the universal transmitter.
SOURCE: failsafe engine mode light comes on, codes
Just a quick mention - for about a month my XK8 low coolant light came on intermittently. This week with no notice while driving normally I got Stability Control Fail and FailSafe Engine Mode and wtih great difficulty got the car back to where I started from (less than a mile). Two days later (when got time) and after a bit of research, I tried it again - same problem and a very unhappy engine. I then disconnected the battery for 15 minutes (probably more) to clear the engine codes as well as check all the wiring and vacuum stuff I could under the hood (at a Jaguar master mechanic's recommendation). No problems found but the car would start and immediately stall with the air intake hose disconnected from the intake butterfly. After I reconnected the air intake hose, she started and purred like normal. The problem is the BATTERY... It is low - I've known it for a LONG time BUT it always started right up and never skipped a beat. I intend to replace it tonight but fully expect that's the issue. I've had the car 6 years (it's a 98) and had NO problems except a dead taillight asembly.
Hope this is of value...
SOURCE: I want 2 change 2004 mercury mountaineer transmission fluid
The best way to change it is to flush it out You can do it yourself, but I do not recommend. A shop that is good like a Monro or Firestone usually charges about 100 bucks to flush and that includes the fluid. If you do it yourself, you will save about 60 dollars, but you risk damage to your radiator.
you will need a hose and an adapter. you back out the lower, or upper cooler line for your trans, whichever is the easiest to get to, (Some trucks have an auxiliary engine oil cooler, but make sure you are flushing the trans lines) put the adapter into the rad where you removed the line, and put a hose from each one down into a bucket. Have about 14 qt's of ford trans fluid ready. Put the funnel into the trans dip stick, and start the engine. pour the qts into the dipstick tube while the old fluid is pumped into the bucket. When you have about two gallons pumped into the bucket shut the engine off and reattach the line into the radiator. start up the engine and check your level. Fill with additional fluid if needed.
note: some say you should drop the pan. two things, you only change half the fluid when you do it that way, and second if you need to change the filter because it is clogged, it is too late for the transmission. The filter is only there to protect the valve body, not keep the fluid clean.
Hope this helps
SOURCE: I HAVE A 2004 MERCURY MOUNTAINEER IT THREW A P2106
Try having the codes cleared, and see what happens.
2,039 views
Usually answered in minutes!
×