Question about Cars & Trucks

1 Answer

ISUZU mu7 timming belt change when

Its done 110000 kilos about 7years old a 3.0 engine size

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 53,755 Answers

Over due for a belt change by 2 years and 10,000 klm

Posted on Jan 23, 2018

Testimonial: "a mu7 dmax engine 3.0 has no timming belt so where do you get the info from"

  • 1 more comment 
  • Bill Boyd Jan 30, 2018

    duh---from your question--duh
    Isuzu run both timing belts and chains depending on the model
    what is a dmax in one country is by another name somewhere else
    and I get my information from 60 years in the trade and from autodata technical publication
    now a question for you
    Why did you specify timing BELT if you knew it is a chain

  • Paul Richard Howling
    Paul Richard Howling Jan 31, 2018

    a d max engine is a GM / ISUZU joint venture the d max is used world wide, top end diesel engine makers all use a chains the belts were made to create more money in the industry, same as the problem with emmission problems in EU they now want to ban all diesel cars creating more money for the industry. at the time i did not know it was a chain sorry for the miss info. regards paul

  • Bill Boyd Jan 31, 2018

    toyota use belts in their diesels and get really good reliability from them
    There is one European car manufacturer that uses a chain from the rear of the engine that drives 1 cam shaft to the from where there is a chain connection to the other cam shafts
    In this country , Isuzu is Isuzu and the GM is a Colorado

×

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1066 Answers

SOURCE: change timing belt

don't chance a engine failure...you ca get timing belt info at the public libuary.  Haynes or Chilton Manuals

Posted on Mar 21, 2009

honeymokey

honeymokey

  • 3113 Answers

SOURCE: remove and replace timming belt on lanos sx 1598cc 1998 thank you

First remove head and fix the bent valves. I have worked at a Daewoo dealer. People would buy the belt and come right back to get valves and gaskets. Daewoo timing belts must be replaced every 60,000 miles.

Posted on Apr 19, 2009

Ted Schore

  • 7353 Answers

SOURCE: FIRING ORDER DOES NOT MATCH MARKING ON TIMMING BELT

replacing the timing belt does not change the firing order. the dist should only go in one way. the firing order is, 1 3 4 2

Posted on Sep 23, 2009

Testimonial: "thank you very much sanjuana"

Larry Chandler

  • 1149 Answers

SOURCE: TIMMING BELT IS THE ENGINE INTERFERANCE?

Hi:
Yes, this engine isn an interference engine, and your valves will get ruined if your timing belt breaks. It is money well spent to replace it , and don't forget to have the water pump and tensioner replaced at the same time!

Posted on Feb 09, 2010

Patrick Rayome

  • 1757 Answers

SOURCE: installing a timming belt on a 2002ptc 2.4 engine no room

Sorry for the delay.
I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt Diagrams that you will need.
Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2002/make/chrysler/model/pt_cruiser/2002_chrysler_pt_cruiser_timing_belt_diagram_marks.htm

Posted on Mar 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I just replaced the alternator belt on my 96 Isuzu trooper and after tightening everything and starting the engine ,neither the fan nor the alternator will turn unless I do so by hand


did belt fall of first or you took it off. first.???????????????????????????????
no engine size stated 2.8L or 3.1L Usa.
belts vary by engine,
causes.
belt mis-routed,did you make a drawing before starting.oops
or you set the tension wrong? read the book or guess?
or the auto tensionor is bad. (we always check this 1st.

now i read your fsm book on serp belt.
its a serp right>?

"some of the V6 engines are equipped with a serpentine belt and automatic belt tensioner. The tension is maintained by a spring loaded pulley/tensioner. The indicator mark on the moveable portion of the tensioner must be within the limits of the slotted area on the stationary portion of the tensioner. Any reading outside the limits indicates either a defective belt or wrong SIZE belt or bad tensioner."

question 3
did you take old belt and match it side to side
with the old, and are same size.
if not FAIL.
assumes old belt not lost or run to total destruction. (im blind tell me)
q4: did you put a a/c belt on a non a/c cars
see dotted line below, that be 2 type belts.

2ba12d2d-204f-43cb-a418-9fc008566245.jpg

Jan 14, 2016 | Isuzu Cars & Trucks

1 Answer

2007 Acura tl 3.2 110000 miles engine makes a clicking noise when idling& driving I'll done the oil change and transmission flush but still haerd the clicking


At 110000 miles it could be:
1. the serpentine belt or one of the idler pulleys
2. the water pump
3. the timing belt or one of its idler pulleys
4. to a lesser extent, the power steering pump
5. a valve lifter
Here is a video showing what is on the front of the engine
You may want to get a mechanics stethoscope and carefully start trying to pinpoint the noise [keep fingers far away from belts and pulleys, I know 3 people that lost finger tips this way].

Feb 03, 2015 | Acura Cars & Trucks

1 Answer

Timing belt idler


The dealer will have a listing for the entire idler. Most shops dont service just the bearings anymore. It's a wash with labor to press them out and back in when you factor the extra time reading the number off the old bearing and getting one since no one lists them.

Apr 06, 2014 | Suzuki Baleno Cars & Trucks

2 Answers

Engine won't start distributor won't turn


no your timming belt broke!!! now if you have a interference engine you will need a new car!!!
the only way to know is if you search your year make and engine size of your car..
you better hope its a non interference engine .. than just change the belt.. good luck. this is a basic timming belt photo . engine-start-distributor-turn-rbr12kxjqsqvwnu2khrshnjz-4-0.jpg

Jun 12, 2013 | Cars & Trucks

1 Answer

Which pulley is the idler pulley on a 2001 isuzu trooper 3.5L,DOHC motor?


stevenhurc_2.jpg 1=crank
2=alternator
3=idler tensioner
4=IDLER
5=fan idler
6=air cond compressor
7=accessory drive belt(serpentine belt)
8=power steering pump

just in case this is the timming belt and pulleys

stevenhurc_3.jpg

Jan 31, 2011 | 2001 Isuzu Trooper

2 Answers

Is it necessary to take the timming belt off to replace the water pump on a 1996 isuzu rodeo


3.2L engine, you will have to remove timing belt to replace water pump, your water pump is timing belt driven, I would replace timing belt while in there, good luck, hope this was very helpful.

May 14, 2010 | 1996 Isuzu Rodeo

1 Answer

Have high tappet noise on my skoda octaivia 1.9 tdi, how do i fix this, changed the timing belt @ 90000km the car has done 110000 km so far


Run a bottle or 2 of "Engine Flush" "or alternatively some people use 200ml kerosene" through the crank case with the car idleing for about 10-15 minutes at normal operating temperature then drain the old oil out, change filter and put in the best quality oil matched to your vehicle specifications.

Mar 09, 2010 | 2005 Volkswagen Jetta

2 Answers

I need a diagram to sincronize the timing belt of my isuzu tropper 3.2 sohc


if this is 6VD1 engine it has single cam gear each head, but is still a 2 cams per head, engine
if belt has broke or you have turned any gear you must remove rocker covers to check positions of camshafts front lobes are in certain spot as well as timming mark on belt driven cam gear to cover
this cam gear is a 3:1 ratio (3 turns of cam gear = 1 turn of cams)
184d763.jpg

Jun 12, 2009 | 1993 Isuzu Trooper

1 Answer

Timing chain or belt for a 2004 Honda Accord


It depends, 4cyl. is a chain, the 6cyl. is a belt and it is an interference engine. I have not done this one yet, but Hondas are never that easy.

Mar 17, 2009 | 2004 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...