My 2017 Honda CRV every warning you can tire pressure break hold system vehicle stability assist problem hill start assist problem drive carefully system brake system problem

check the tire pressures for your vehicle on the inside of the driver door. If the correct pressures don't reset this light you may have a bad sensor inside the tire. This is not an average guy type fix because you can't tell which is bad without the right sensor reading tool and the new sensor has to be calibrated to the car. Les Schwab may do these.

You have damage to the front area brake system. It could be very serious but if car stops OK most likely not that serious you just won't have abs or traction control. The damage is most likely a speed sensor or something similar. I said it could be serious that is only worst case.
Here is a breakdown of what lights mean
ABS keeps your breaks from locking up
BREAK ASSIST helps your breaks
Traction control if you one wheels spin more than others system adjust wheel spiN

If the explanation point is inside of what looks like a tire. Tire Pressure Monitor System. Inflate your tires to the correct pressure (probably 32psi) Or could be an issue with you TPMS

Hi, the tire pressure monitor detects any changes in the tire inflation pressure. Therefore, it must initialize and store it in its memory if the tires or wheels have been replaced, re-inflated or the tires have been rotated. You can re-initialize the system by following these steps:

1. Check and make sure that your tires are inflated to the correct pressure

2. Turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (in the glove box) until the warning light turns off and then release the switch.

3. Now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. Initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Don't waste your money on unnecessary sources and unwanted repairs.. get this manual online at www.reliable-store.com u will know whether
to repair or not, service it, and how to repair etc

The Vehicle Stability Assist system is turned off. Vehicle Stability Assist (VSA) is an electronic stability control system that works in conjunction with the Pilot's drive-by-wire throttle and its 4-channel ABS systems to enhance controllability while the vehicle is accelerating, braking, cornering or when the driver makes a sudden maneuver. VSA functions by applying brake force to one or more wheels independently while also managing the throttle, ignition and fuel systems to help the vehicle maintain the driver's intended path of travel.

You need to find the VSA button on the dash and push it, this will activat the VSA and turn off the yellow light.

Standard Vehicle Stability Assist™ (VSA ®) with Traction Control and Brake Assist Vehicle Stability Assist (VSA) is an electronic stability control system that works in conjunction with the Pilot's drive-by-wire throttle and its 4-channel ABS systems to enhance controllability while the vehicle is accelerating, braking, cornering or when the driver makes a sudden maneuver. VSA functions by applying brake force to one or more wheels independently while also managing the throttle, ignition and fuel systems to help the vehicle maintain the driver's intended path of travel.

The VSA system constantly analyzes data from seven sensors that monitor wheel and vehicle speed, steering input, lateral G forces and yaw rate. It compares the driver's control inputs with the vehicle's actual response. Whenever the actual response falls outside of a predetermined acceptable range, VSA intervenes with a corrective action.


For instance, if VSA detects an oversteer condition, the system may apply braking force to the outside front and rear wheels to counteract the unintended yawing effect. In the event of understeer, VSA may apply braking to the inside rear wheel while reducing engine power to help return the car to its intended course. VSA also provides a limited-slip differential effect for the front wheels by applying braking force to a slipping wheel, thereby redirecting driving force to the wheel with more traction.

There is a button on the lower left part of the dashboard that says "VSA". Push it and the triangle will dissappear (this should only be turned off if you are using a spare tire that is smaller than the rest of the tires).

Good luck.

the check engine lamp is not affected by things like tyres, brakes etc. It shows that the vehicles engine management system had detected a fault with the engine or engine sensors. Check the engine for broken or disconnected wiring (maybe it was disconnected during the replacing of the hoses but not reconnected). If you fail to locate anything, check the manual for the correct fault code retrieval procedure or take the vehicle to a professional. Tyres may affect your ABS system or Airbag systems but they usually have their own warning lamp and are unrelated to the check engine lamp..

That isn't the light for low tire pressure. Low tire pressure will have what looks like a tire- flat. It is your VSA someone probably hit the button and accidentally. look to the left of your steering wheel there is a button that says VSA push it and see if it turns it off. I notice that this post is pretty old, so you may already have gotten the answer from your dealer, but I'm posting in case someone has the same problem later on.