SOURCE: replaced slave cylinder 2004 ford ranger 4x4 still no pedal
I had the same problem with my 1995 1500 p.u.. Assuming your clutch slave cylinder is the concentric style. If not disregard. I hate that set up. what the hell was wrong with the old outside of the bell housing slave/ mechanical style fork and throw out bearing bla bla? Its because ford as well of the rest of the lovely auto makers decided long ago to make them as hard as hell to repair on you own. Ive been told theres a spsecial tool just for this bleeding task. Pobably. They make those tools to sell to us so they can further profit from us poor suckers.Also I wonder on your model if its concentric, does it have the difficult sized bleeder valve as mine did? or have they gotten a little more user friendly? doubt it. In my case as this style is a closed system I followed the bleeding intructions to a tee. That did get alot more clutch action for me, after 15 attempts.However I do believe the problem after looking and further inspection under the dash? look up under the dash and inspect your pedal rack and frame. I found mine was cracked and the cause of poor aliegnment. check for that rite away. I located another rack but before I got around to replacing it, the tranny blew, and the trucks sitting on my dads property. Its still a danmed good truck and one of these days I will get on it again. Anyway up untill the tranny blew I was never able to get more than half the distance from the pedal and besides the rack problem I would love to know the bleeding anser, that is if Im off target. Going to be up against it again when I replace that transmission. Hope this helps a little. Food for thought maybe? If you find out something more helpful post it so I will know too.
SOURCE: 300Zx will not shift out of 5th gear
Dear javatrader: There are very few solutions to this problem. The fact that you had mentioned 5th & Reverse, tells me that you problem is has two possibilities. Both relate to the same component.
The shift fork for Fifth gear and reverse are the same as well as the hub which the fork fits over.
When you Move the stick shift, it moves one of 3 rails in the transmission of which one is 5th and reverse. The hub is what locks the transmission in gear. The gears are what are referred to as synchromesh. This means that when you shift from gear to gear, it makes it possible to easily make the transition without the gears grinding while the car is in motion. The synchros are in fact, kind of a "BRAKE" for the gears so that when you go to shift into that gear, the synchronizing ring, slows the gear down enough to match the speed of the counter gear allowing it to engage with it, without grinding. As the hub slides into gear, there are spring loaded "KEYS" which are small pieces of steel about 1/2 inch long, 1/4 inch thick and 1/4 inch wide with a little hump in them to push up into a small cavity machined into the hub when it slides over it, thus locking the gear into place until you pull the stick to move it out of place. If a key pops out, it could cause the gear to stick, not allowing you to pull the hub back because the key has popped out at an angle which prohibits the hub from sliding over it.
Another possible senario: The fork is secured to the shift rail with a part called a "Roll pin". If this part shears, the car will be stick in what ever gear it was in at the time the pin sheared. If the pin shears, the stick will still move out of 5th gear position but the transmission won't.
This problem, unfortunately is not one a layman can fix. This is best left to a professional.
Good luck......If you are pleased with my answer, please write in, that you are satisfied with my answer. I am new in this "FIXYA" group and need more people responding to work my way up the ranks.
SOURCE: 1997 hyandai accent gt clutch problem
hi considering age of car and that you have no leaks on hydraulics? may i suggest you try bleeding the clutch to rid of old fluid a couple of pumps may be suffice ? b/fluid does absorb moisture and heat over time hence recommendation tat fluid be changed at period specified in handbooks ie 12 monthly ?
SOURCE: put in new clutch and slave cylinder. no clutch pedal. how do you bleed the cylinder?
work it back and forth with your hand and you will get pedal after a while then bleed like you would brakes get help so one can pump and the other can bleed
SOURCE: clutch pedal stays 2 the floor on a hydralic
Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.
258 views
Usually answered in minutes!
×