20. INSTALL CYLINDER HEAD COVER SUB-ASSY
(a) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes after
applying seal packing.
Do not start the engine within 2 hours after installing.
(b) Install the cylinder head cover with the 9 bolts. Tighten the
bolt uniformly in several steps.
Torque: 8.0 Nm (80 kgf cm, 71 in.lbf)
(c) Install the engine wire harness with the 3 nuts.
Torque: 8.4 Nm (85 kgf cm, 74 in.lbf)
21. INSTALL CYLINDER HEAD COVER SUB-ASSY LH
(a) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes after
applying seal packing.
Do not start the engine within 2 hours after installing.
(b) Install the cylinder head cover with the 9 bolts. Tighten the
bolt uniformly in several steps.
Torque: 8.0 Nm (80 kgf cm, 71 in.lbf)
(c) Using an E6 torx) socket wrench, install the engine wire
harness protector with the 2 bolts.
Torque: 8.4 Nm (85 kgf cm, 74 in.lbf)
This is year/make/model specific to the 2nd Gen Sienna. Taken from the 05 Toyota Sienna repair manual. Hope this answers your torque specs for the valve covers which uses 10 mm bolts. If in doubt, as Scotty Kilmer asserts, do a "German tight".
SOURCE: Escort Mk2 1600 valve and torques settings what are they
cylinder bolt torque settings stage 1 15 ft pounds
stage 2 50 ft pounds
stage 3 85 ft pounds
valve clearences 0.15 - 0.20mm inlet
0.22 - 0.27mm exhaust
these are the figures i have been supplied with, you can also use
cylinder bolts stage 1 10 ft pounds
stage 2 50 ft pounds
stage 3 + 90deg.
with my exp, i would use the first guide as the degree method has a tendancy to snap head bolts, especially on older vehicles.
SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS
You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM
SOURCE: whats the torque setting for big end bearing bolt
hi big end bearings are two stage, 25nm leave ten mins, then 49nm cylinder head bolts three stages 20nm leave ten mins, 40nm leave ten mins then 60nm check after 5,000miles hope this helps
SOURCE: i need torque specs for a 2004 dodge cummins 24
http://www.dieseltruckresource.com/dev/index.php
I suggest this website for your dodge truck needs.
SOURCE: whats the valve clearance for toyota 4k engines
valve clearance is .20mm for the intake and .30mm for the exhaust. Will try to find cylinder head torque for you.
2,859 views
Usually answered in minutes!
20. INSTALL CYLINDER HEAD COVER SUB-ASSY
(a) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes after
applying seal packing.
Do not start the engine within 2 hours after installing.
(b) Install the cylinder head cover with the 9 bolts. Tighten the
bolt uniformly in several steps.
Torque: 8.0 NVm (80 kgfVcm, 71 in.Vlbf)
(c) Install the engine wire harness with the 3 nuts.
Torque: 8.4 NVm (85 kgfVcm, 74 in.Vlb
This was directly taken from the 05 Sienna Repair Manual. But as the other fellow stated in his answer, I would do a "German tight" version to prevent stripping and damage to the cylinder head.
×