I reset airbag light once driven for a short distance it starts flashing red again
Have you check at the dealer ? Recall on defective air bag .
2007 2012 Nissan Versa Recall Alert News from Cars com
SOURCE: blinking airbag dashlight Nissan Versa
First, turn on your car (ON key position) and your airbag light stays on for 7 seconds, then starts flashing every half second. (.5 seconds on, .5 seconds off, repeat)
This means either your airbag is malfunctioning, or it malfunctioned in the past. We'll find out exactly what happened in a second.
If your airbag light is on solid the whole time, either your airbag has deployed, the computer thinks its deployed, or your sensor or wire harness is broken. You're going to need a professional to fix this.
If your light never comes on at all, your METER fuse might be blown, or you might have a wiring fault in an airbag circuit. Go directly to Infiniti and have a professional fix this.
OK, so your light is flashing like I explained before. Next, we're going to enter DIAGNOSIS mode. This mode will tell you exactly what’s wrong with your airbag (according to the computer at least) It's a bit tricky, but read carefully.
1. Turn ignition switch “ON”.
2. After “AIR BAG” warning lamp lights for 7 seconds, [i.e. when it stops running solid and starts flashing] turn ignition switch “OFF” within 1 second. [DO NOT SWITCH IT TO LOCK, SWITCH IT TO ACC]
3. Wait more than 3 seconds.
4. Repeat steps 1 to 3 two times. (Perform 3 times in total.)
5. Turn ignition switch “ON”.
SRS is now in Diagnosis mode.
Try it a few times. If you can't get it to work, have someone else try. If you STILL can't get it to work, check your battery voltage. It might be low.
In diagnosis mode, you're going to hope the light flashes slowly. 2 seconds off, 3 seconds on, and repeats. If your light does this, this means that the computer detected a previous error that hasn't been erased. This is good.
If you get ANY OTHER result, go directly to Infiniti. You've got a real problem that needs a real fix.
Now, to erase the error from memory.
5. If “AIR BAG” warning lamp operates as [as I said before], turn ignition switch “OFF” to reset from Diagnosis mode
to User mode and to erase the memory of the malfunction.
6. Turn ignition switch “ON”. “AIR BAG” warning lamp operates in
User mode. [it should stay on for 7 seconds, then go off, like normal.]
Hope this helps you.
SOURCE: won't start after driving short distance
I would check any recalls. I had a 2000 Nissan Sentra and the crankshaft position sensor was the problem. It may be a warranty replacement item.
see this
http://nhthqnwws112.odi.nhtsa.dot.gov/acms/docservlet/Artemis/Public/Recalls/2007/V/RCDNN-07V527-8115.pdf
SOURCE: 2007 Sienna airbag warning lamp flashing
Certainly check with your Toyota Dealer as the vehicle is hopefully is still under factory warranty at that milage. The Air bag light flashing is certainly cause for concern, and having an airbag set off without impact can be very dangerous and it is best to have a professional working on your airbag issues.
SOURCE: putting car into reverse after having driven short
You need a new Pressure Control Solenoid Body. 9L2Z7G391A -solenoid pack for a 5R55S Trans. $332.20. at Trans Parts supplier. Don't even call a Lincoln Dealer for a price. They wouldn't even deal with me because I have a sales tax ID, and ask too many question. They will screw you over big time. That's a common problem in a long list of LS issues, my wife has one also and I used to have a Trans Repair Shop. It will slam into Reverse cold, Slip or flair on 3 to 4 Shift. Also expect the EGR Valve to go bad and make the trans issue even harder to troubleshoot, untill it works correctly. Drop the tran pan, remove about 7 screws and change the solenoid body. Best bet, go to a trans shop, never a dealer. Also get the old fluid out of there and put Mecon V in ,with a bottle of Red Lubgard Additive.
SOURCE: how to change a headlight on nissan versa 2007
How to change a headlight on Nissan Versa 2007. Open the hood, pull the power cable off of the headlight. Peel off the large black rubber cover. There is a metal clip you must push in and then out to unclip. The bulb will then slide out for replacement.
1,981 views
Usually answered in minutes!
×