Question about Toyota Previa

Open Question

Can i change trailing arms on my previa 2001 without taking everything off

On rear of the vehicle

Posted by on

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
dttech

dttech

  • 4803 Answers

SOURCE: Want to know the relationship

The recall for your vehicle may or may not have included replacement of the trailing arm. The recall says that the trailing arm is to be "inspected" then it will be replaced, or modified at the discresion of the person performing the inspection. If it was "replaced", it would require the control arms to be disconnected and reconnected. If it was only "modified" there would have been no disassembly of the control arms required. See the picture below. The picture shows the rear suspension parts. Notice that the upper control arm and the lower control arm bolt to the trailing arm. (which is what also houses the hub and bearing with the wheel speed sensor.) I hope this helps you to resolve your issue.

dttech_35.gif

Posted on Mar 08, 2011

Ad

Miranous

  • 2 Answers

SOURCE: front bushes on rear trailing arms.........is it

Yes but you'll need special toolset, I think it's PI-A0048-REV B for that model.
You can make your own with threaded rod and large washers & tube if you're in the mood for it.

Posted on Mar 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove rear A/C expansion valve on 2001 Chrysler Town and Country


Next remove the rear seats or stow them. Then remove all the trim panels from the passenger rear of the vehicle. You will then be able to see the rear HVAC assembly.

Jack up the vehicle and support it properly. remove the nut that holds the rear lines to the expansion block.

Remove the heater core form the HVAC module with the cooling lines still attatched. Remove the HVAC module from the vehicle.

You will then be able to replace the rear evap core/tubes/expansion valve.

Get the kit from the dodge dealer. It will make life very easy.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Aug 13, 2015 | 2001 Chrysler Town & Country

1 Answer

I have a 2000 Lincoln Navigator It has a Air Suspension System on it, I acquired this vehicle from a "friend" suposedly abou one month ago besides other small problems I had with it last week I...


Between the rear axle and the body you should see a plastic arm that connects between them. If the arm breaks it will allow air to bleed from the rear airbags and keep the compressor running.

Jun 13, 2011 | 2004 Lincoln Navigator

1 Answer

Not much access to the spark plugs


depends upon what vehicle your dealing with, if it`s a rear wheel drive V6-V8 vehicles, usualy you can get to them easier thru the wheel well. Front wheel drive V6-V8 vehicles are easy for front of vehicle access, and under vehicle access to get at the ones facing towards the rear of the vehicle.

Apr 26, 2011 | Chevrolet Astro Cars & Trucks

1 Answer

How to disassemble the rear end in a 2000 gmc yukon and how to remove axles


Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Loosen the lug nuts on the wheel and tire assemblies but do not remove the lug nuts
  3. Raise and support the vehicle
  4. Remove or disconnect the following:
    • Wheel and tire assemblies
    • Axle lubricant into a suitable container
    • Rear driveshaft
    • Parking brake cable
    • Brake calipers
    • Shock absorbers from the axle brackets
    • Vent hose from the rear axle vent fitting
    • Nuts and the washers from the U-bolts
    • U-bolts, spring plates and spacers from the axle assembly
  5. Lower the axle assembly from the vehicle
To Install:
  1. Place the rear axle assembly under the vehicle
  2. Align the rear axle assembly with the springs then connect the spacers, spring plates and the U-bolts to the rear axle
  3. Raise the rear axle assembly into position
  4. Install or connect the following:
    • Washers and nuts to the U-bolts; Torque to: 59 lb-ft. (80 Nm) then, Torque to: 89 lb-ft. (120 Nm)
    • Vent hose to the rear axle vent fitting
    • Shock absorbers to the rear axle
    • Brake calipers (See: Brake Caliper)
    • Parking brake cable (See: Parking Brake Cable)
    • Rear driveshaft (See: Rear Driveshaft)
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  5. Fill the rear axle with lubricant
  6. Bleed the brake system (See: Brake Bleeding)
  7. Install the wheel and tire assemblies
  8. Lower the vehicle to the ground
  9. Torque lug nuts as follows:
    • Single Wheel: Torque to: 140 lb-ft. (190 Nm)
    • Dual Wheel: Torque to: 175 lb-ft. (240 Nm)
  10. Road test the vehicle to check performance
prev.gif next.gif

Aug 03, 2010 | 2000 GMC Yukon XL

1 Answer

When do you change the fluid in the rear differencial. I was told by a mechanic that the rear differencial fluid was low and had metal shavings in it, and that the fluid needed to be changed and that it...


I'd say yes. The differential fluid is often overlooked by oil change technicians, even though it's something that should be topped off periodically.

It probably would cost more than that to repair it once it wears out.
Axle Housing Assembly Removal & Installation To Remove:
  1. Lift the vehicle.
  2. Drain the lubricant from the rear axle housing.
  3. Remove the rear axle assembly from the vehicle.
  4. Remove the brake caliper brackets from the rear hubs.
  5. Remove the rear cover and gasket from the rear axle housing.
  6. Remove the rear axle shafts from the vehicle.
  7. Remove the rear differential assembly from the vehicle.
  8. Remove the brake backing plates from the rear hubs.
  9. Remove the rear drive pinion shaft yoke and seal from the drive pinion.
  10. Remove the drive pinion from the rear axle housing.
To Install:
  1. Install the drive pinion into the rear axle housing.
  2. Install the rear drive pinion shaft yoke and seal onto the drive pinion.
  3. Install the rear differential assembly into the vehicle.
  4. Adjust the differential side bearing preload and the backlash.
  5. Perform a gear tooth contact pattern check.
  6. Install the brake backing plates onto the rear hubs.
  7. Install the rear axle shafts into the vehicle.
  8. Install the rear cover and gasket onto the rear axle housing.
  9. Install the brake caliper brackets onto the rear hubs.
  10. Install the rear axle assembly into the vehicle.
  11. Refill the lubricant in the rear axle housing.
  12. Lower the vehicle.
prev.gif next.gif ---
I think that changing the fluid would take about an hour, and depending on the garage, and the labor rate, that they might elect to take the rear cover off of the differential, and drain it that way and replace the fluid once it was put back on. He could inspect the gears while the cover was off and tell you how bad it was.'

Do you hear any clunking or gear mesh noises from the rear when putting it in gear or running the vehicle?


Some mechanics would simply top off the fluid and wait until it wears out, which could be several thousand miles in the future.

Use gear oil for it of the recommended viscosity in the service manual.

Generally thicker than motor oil.

So, adding fluid would cost only the amount of the fluid plus some labor.
A bottle of fluid might cost $9.99 or so depending on where you get it.

You might be able to do this yourself if you crawl under there, remove the fill plug at the top, and just add gear oil. If there isn't enough room you might drive it up on some ramps and then crawl under there.

Jul 29, 2010 | 2004 GMC Envoy

1 Answer

Do i have to remove the back seat to take rear struts off


Answer
REMOVAL - SHOCK ASSEMBLY
NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.

Roll back carpeting on top of the rear shock tower to access shock mounting nuts.
Remove plastic cover from the top of the shock assembly.
Remove 2 nuts attaching the shock assembly upper mount/spring seat to the shock tower.
Raise vehicle on jackstands or centered on a frame contact type hoist. (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE)
Remove the rear wheel and tire assembly from the vehicle.
Remove two fasteners holding the splash shield to the shock assembly upper mount.
Remove bolt attaching shock absorber to rear knuckle (Shock Absorber Attachment To Knuckle).
Remove the shock absorber from the rear knuckle first when removing the shock absorber from vehicle by pushing down on the rear suspension.
Move shock assembly downward and tilt top of shock outward, then remove shock assembly from vehicle through top of wheel opening

Nov 23, 2009 | 2002 Dodge Stratus

1 Answer

The function that rsiaes and lowers the vehicle doesn't work,


Lifting

The following instructions must be carried out before raising the vehicle off the ground.

  • Use a solid level ground surface.
  • Apply hand brake.
  • Select 'P' on automatic gearbox selector.
Note: If the propeller shafts are to be removed, reference must be made to the relevant operation. To avoid damage occurring to the under body components of the vehicle the following jacking procedures must be adhered to.

DO NOT POSITION JACKS OR AXLE STANDS UNDER THE FOLLOWING COMPONENTS:
  • Body structure other than approved jacking points
  • Bumpers
  • Fuel lines
  • Fuel tank
  • Brake lines
  • Front or rear suspension arms
  • Transfer box
  • Steering linkage
  • Front or rear differential units
  • Engine sump
  • Automatic gearbox
NOTE: For certain repair operations, it may be necessary to support the engine under the sump. In this case, a block of hardwood or a rubber block should be positioned on the jack lifting cup to protect sump. Vehicle jack
The jack provided with the vehicle is only intended for use in an emergency, for changing a tyre. DO NOT use the jack for any other purpose. Refer to Owner's Handbook for vehicle jack location points and procedure. Never work under a vehicle supported solely by the vehicle jack.

Hydraulic jack
A hydraulic jack with a minimum 1500 kg, (3,300 lbs) load capacity must be used.

WARNING: Do not commence work on the underside of the vehicle until suitable axle stands have been placed in their correct position. Always chock the wheels when jacking. The handbrake may be ineffective when the wheels are off the ground. Raising and supporting the vehicle
To assist in raising the vehicle, jacking points are provided as shown in the following illustrations.

Raising the front of the vehicle
Apply handbrake, select 'P' on automatic gearbox selector and chock rear wheels.
Axle stand positions - front

Raise vehicle to enable axle stands to be positioned under, either, the front sub-frame, or the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.
Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack.
Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Raising the rear of the vehicle
Select 'P' on automatic gearbox selector and chock front wheels.

WARNING: Always chock the front wheels when jacking the rear of the vehicle.

Axle stand positions - rear

Raise rear of vehicle to enable axle stands to be positioned under the rear sub-frame. Alternatively, the axle stands may be positioned under, either, the recommended customer jacking points or the front mounting points of the rear sub-frame.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If any damage occurs to the washers on the front mounting points of the rear sub-frame, then the washers must be replaced. Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack. Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Wheel-free lift
The following warning must be read before attempting to lift the vehicle.

WARNING: The vehicle cannot be supported safely in a wheel-free condition using the wheel-free facility of a four post ramp, and under no circumstances must this method be employedA wheel free condition may only be achieved on a four post ramp by raising each end of the vehicle and positioning axle stands beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox. WARNING: The front and rear suspension lower arms must NOT be used as lifting / jacking points. Alternatively, support the vehicle on an approved two post lift with the arms of the lift beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between the lifting equipment and the jacking points to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.

Oct 04, 2009 | 2003 Land Rover Range Rover

1 Answer

Calibers locking up on 94 toy pickup


go to the rear of the vehicle and look just above the rear end, there is a load sensing porpotioning valve up there, there is a rod that connects the rod to the top of the rear end, if you have raised or lowered the vehicle than that rod needs to be adjusted,

the valve simply diverts fluid to and from the rear brakes depending on rear vehicle ride height, this is for proper stopping ability when the vehicle is loaded down or when it nose dives from a hard stop.

let me know if this helps

wesleyschacht@hotmail.com

Jun 14, 2009 | 1994 Toyota Pickup

1 Answer

EXPEDITION REAR AIR RIDE PROBLEM


do you have just rear air suspension? here's rear only. 4 wheel different. Deler an run a diagnostic test with WDS machine and get fault codes.
-------------------------------------------------------------------------------------
The air suspension system is designed to improve ride, handling and general vehicle performance for static, on-road and off-road driving conditions:
  • Ride is improved by using an air type spring (the soft ride is inherent).
  • Handling is improved by maintaining constant vehicle attitude.
The system consists of unique rear air springs, the air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for the RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines and the use of air springs with air spring solenoids.
The air suspension system holds vehicle height when the rear hatch or any door is opened. The system stores rear vehicle height the moment any open door is detected. The system then maintains this height regardless of the addition or removal of a load. The system will return to its commanded height when all doors are closed or the vehicle speed exceeds 16 km/h (10 mph).
----------------------------------------------------------------------------------------
Air Suspension Height Sensor
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3.2 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm (3.2 in) of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket).
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level
------------------------------------------------------------------------------
  • Uneven vehicle height
  • Circuitry.
  • Rear pneumatic fault.
  • Air compressor assembly.
  • Air suspension control module.
  • Go To Pinpoint Test I .

Feb 21, 2009 | 2001 Ford Expedition

1 Answer

2004 dodge stratus SE


This is a dangerous job if you do not have the proper equipment for compressing the spring that is around the rear shock. I do not recomend performing this job without the proper equipment. Unloading the spring without it compressed can cuase injury.

If you have the proper equipment this is how you do it.

REMOVAL - SHOCK ASSEMBLY NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.
  1. Roll back carpeting on top of the rear shock tower to access shock mounting nuts.
  2. Remove plastic cover from the top of the shock assembly.
  3. Remove 2 nuts attaching the shock assembly upper mount/spring seat to the shock tower.
  4. Raise vehicle on jackstands or centered on a frame contact type hoist.
  5. Remove the rear wheel and tire assembly from the vehicle.
  6. Remove two fasteners holding the splash shield to the shock assembly upper mount.
  7. Remove bolt attaching shock absorber to rear knuckle
  8. Remove the shock absorber from the rear knuckle first when removing the shock absorber from vehicle by pushing down on the rear suspension.
  9. Move shock assembly downward and tilt top of shock outward, then remove shock assembly from vehicle through top of wheel opening.

Aug 04, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...