Timing marks for 2006 hyuandai elantra 4cyl

There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

I just recently experienced the same problem. The timing is 180 degrees out. Unfortunately the only way to correct it is to take the engine apart again. Set the right hand camshaft to TDC by using the marks on the timing gear for that bank. The left will follow to the degree it can although you will have to manually hold the cam in position when you put the timing gear back on. Now you can remove the timing chain. The crank TDC indicator may not be right on but it will be close. Rotate the crank CW one revolution to the point the TDC marks are lined up. Now install the timing chain according to the instructions. The timing gears on the camshafts will only go on one way as the bolt holes are slightly off the extreme diameter of the gear. If you put the chain back on making sure that all the marks are proper, she'll fire on the second cylinder up. Not a fun job I know, but when everything works right, you do get a sense of satisfaction.

04 elantra 2.0 L doesnt have 2 cams?

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f803785d2


http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f80377ddf


http://www.autozone.com/autozone/parts/2001-Hyundai-Elantra/Camshaft-Position-Sensor/_/N-jfde6Z9gsn2?filterByKeyWord=cam+sensor&fromString=search

timimg marks for camshafts are notched in the top of the cylinder head. they shuld line up directly in the middle of the 2 smaller cam gears behind the new belt should come with lines on it to make it easier crank to be lined up with keyway slot to the right again the belt should have a ditted line on it for that remember remove the tensioner pushrod assembly and put it in the vice to depress it line the holes up in the body of it and put a 1/4 in allen key through it when you refit remove the key turn it over twice all good

the camshaft is the dot on the sprocket there is a small mark behind it on the cover 12 oclock the crank there is a mark on it look to the ten oclock number 1 tdc you will see the mark

get the #1 piston top dead center, then line up the camshaft gear and the crank gear to line up with the timing marks on the engine after you find those marks slip the belt on making sure all the timing marks havent changed then check to see if the tensioner for the belt is set with the proper tension then check to see if the belt isnt slipping remember it will be spinnig at high RPMS

To the best of my knowledge the 1998 Hyundai Elantra has only a 1.8L (1796cc) engine. Are you sure on the 1.6L?

For the 1.8L:
Firing Order:
1-3-4-2
Cylinders:
(back of engine)
1-----2-----3-----4
(front of engine)
Ignition Connections:
(back)
o<---1
o<---4
o<---3
o<---2
(front)

As far as the markings on the outside of the engine, I'm not aware of any. However, by placing markings (white paint) on the Crankshaft Pulley (lip) and using the Timing Strobe you can get a relative idea. However this is not totally accurate, as the Camshaft Position is not visible. With a 4-Cylinder Timing symptoms will be very obvious.
Click on the following Link. It has the Timing Marking Diagrams for the inside of the engine.
http://www.2carpros.com/car_repair_information/year/1998/make/hyundai/model/elantra/1998_hyundai_elantra_timing_belt_diagram_marks.htm

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

1986 Dodge Truck RAM 50 4WD 2.6L 2BL 4cyl

Fig. Timing belt and components-2.0L engine



Fig. Location and correct alignment of timing marks for the timing belt (camshaft)



Fig. Timing marks-2.3L diesel engine



Fig. Timing marks-2.4L engine



More details, autozone.com (free register). Good luck.

Dear Friend
Removal: Support engine: remove -engine mounting, auxiliary drive belt, water pump pulley, crankshaft pully bots & crankshaft pully, timing belt covers....turn crankshaft to TDC on No 1 cylinder, ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket & balancer shaft sprocket timing marks lighned. Pls note: Timing marks on camshaft sprockets should align with cylinder head uppter face, dowl pins on camshaft sprockets should face downwards....Slacken tensioner botl. Move tensioner away from belt & tighten bolt.
Remove: automatic tensioner unit bolts, automatic tensioner unit, timing belt, crankshaft bolt, crankshaft sprocket, crankshaft sprocket guide washer...slacken balancer shaft belt rensioner bolt, move tensioner away from belt & lightly tighten bolt...Remove balancer shaft belt.

Installation:
ensure timeing marks aligned.Note: Timing marks on camshaft sprockets ahould align with cylinder head upper face, exhaust sprocket mark is on recess but inlet sprocket mark is on tooth. To check oil pump sprocket positionded sorrectly: remove blanking plug from cylinder block, insert 8mm diameter Phillips screwdriver in hole. ensure screwdriver is inserded 60mm from face of cylinder block. If screwdriveer can only be inserted 20mm-turn oil pump sprocket 360". Inset screwdiver again.
Fit balancer shaft delt in anti-clockwise direction starting at crandkshaft sprocket....Slacken balancer shaft belt tensioner notl, turn tensioner clockwise to tension belt. Tighten bolt to 15-22 Nm... Applu thump pressure to belt at tentioner, belt should deflect 5-7mm. If not: Repeat tensioning procedure.... Install - chankshaft sprocket guide washer & crankshaft sprocket.
Thighten crankshaft centre bolt, tightening torque:110-130Nm. Please note, ensure crankshaft sprocket guide washer is fittet correctly. oil threads & contact face crankshaft botl before fitting.