Cars & Trucks Logo

Related Topics:

Older Titan front door lever handle. I got the interior lever handle off, but I can't get the brass cover plate off the interior screws. What am I missing?

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Aug 23, 2008

SOURCE: broken outside door handles (front

I have the same problem on a Toyota Tercel 1997. I am trying to remove the door panel with the door closed (I can not open the door because the door knob is stuck in the lock position). I think I will have to cut through the panel. Have you found something ? My e-mail is [email protected]

Ad

Anonymous

  • 840 Answers
  • Posted on Jan 27, 2009

SOURCE: 07 Yukon Interior door handle peeling

no special tool its easy take mirror cover of inside that is then look for little caps take them off and then take screws out look aroung=d the trim pull out at bottom then pull on sides thenpull up and out the take or unhook switch panel take off trim take off vapor barrier then replace handle wallla then go back

Anonymous

  • 1986 Answers
  • Posted on Aug 14, 2009

SOURCE: how to remove front passenger side interior door panel

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Anonymous

  • 1986 Answers
  • Posted on Sep 04, 2009

SOURCE: rightside interior door handle not opening door

It could mean the rod connecting the handle to the latch has broken. You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. and you can access the innards of the door

Anonymous

  • 1 Answer
  • Posted on Oct 07, 2009

SOURCE: broken passenger door handle

Same problem. I have a 2000 Suzuki Esteem GL. A year ago the driver's door handle broke. Heard a sound and then it was loose. Could not open it from outside. Had to open front passenger door, open the driver's door from inside and then go out again to enter from the driver's door. FRUSTRATING. My mechanic had to take the door apart to fix it. Just a week ago, my front passenger door died on me. Can't open it from outside nor inside. The door won't open. This is such a stupid problem that costs lots to repair. Never will buy a Suzuki again. Had too many problems with it (had to fix gas tank, doors that won't open, front axle...).

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2helpful
2answers

Remove interior door panel 2002 Chevy tracker

No you don't need any special tool . Find all screws on out side of door trim panel and the window handle , the mirror cover plate , then just pull on edge of the panel .
Gently pry the front side door trim panel (3) from the front side door by disengaging the plastic retainers which secure the panel.
Position the door trim panel (3) away from the door in order to gain access to the front side window switch electrical connector, if equipped.
Disconnect the window switch electrical connector, if equipped.
Remove the door trim panel (3) from the vehicle.
Remove the front side window switch from the door trim panel (3) by releasing the 4 plastic retaining tabs, as needed.

Use a cloth in order to pull off the snap ring which secures the front side door window regulator handle (1), if equipped.
Remove the window regulator handle (1), if equipped.
Remove the front side master window switch, if equipped. Refer to Power Accessory Switch Panel Replacement .

Remove the front side door inside handle (1). Refer to Front Side Door Inside Handle Replacement .
Remove the outside rearview mirror opening cover (2).
Remove the screw which secures the front side door pull handle (4).

Front Side Door Inside Handle Replacement
Removal Procedure
Remove the screw which secures the front side door inside handle (1).
Slide the inside handle (1) forward in order to release the retaining tabs which secure the handle to the door.
Open the front side door inside handle rod retainer and remove the front side door inside handle rod from the inside handle (1).
Remove the inside handle (1) from the vehicle.

Check out youtube video showing how to do it !
How To Remove Install Front Door Panel Suzuki XL 7
tip

Door handle repair for Ford fusion

The door handle will not allow unlocking from the inside. This is a common problem with the Ford Fusion 2007 to 2012 and other cars. A cheap piece of plastic breaks that connects the lock lever with the door handle. You can roll down the window and unlock from the outside or hold both levers together and pull open from the inside. This is a very simple repair. Go to any of many web sites for auto parts and buy a replacement. I bought a Dorman 81702 Ford/Lincoln/Mercury Interior Front Driver Side Replacement Door Handle. I popped off the lid that covers a hidden screw inside the recess of the door handle. You have to use a torque bit to unscrew the screw. I then unscrewed the torque screw holding the upper part of the door panel that is opposite the door hinge. The upper part of the door panel can be be carefully pulled away with moderate pressure allowing access to the door handle mechanism. One more bolt holds the door handle part in place. Pull out the broken door handle part, remove the locking cable and put in the new part. Reverse the process to finish up. The whole process took about 10 minutes.
0helpful
1answer

Removing a non locking broadway schlage door lever handle. Unscrewed tiny screw to remove handles but can't figure out how to remove the rest of it from the door. I don't see any screws and can't pull it...

Hi there,

There will be two screws under the decorative cover plate. This cover plate is usually removed with simply pry away from the door slab. Just remember the cover plate is thin, so your pry only need to just be under it, not the actual handle body.



25513107-4uy5lyvd0li3aurgbr2fopza-4-0.png
0helpful
1answer

Remove door panel

Expedition Trim Panel Removal

NOTE The door glass must be completely raised.
  1. Remove the window control switch plate.
  2. Remove the door handle bezel.
    WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  3. Remove the two bolts and three screws, and remove the door trim panel.
  4. Remove the finish cover to access the two center screws.
  5. Disconnect the electrical connectors.

    zjlimited_454.jpg

    Fig. Expedition - Trim Panel Screws shown

  6. Remove the door handle bezel.
  7. Use service notch.
    WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  8. Remove the two bolts and three screws, and remove the door trim panel.
  9. Disconnect the electrical connectors.

    zjlimited_455.jpg

    Fig. Navigator - Trim Panel Screws shown

  10. Position the water shield aside.
  11. If equipped, disconnect the lock cylinder rod.
  12. Disconnect the exterior door handle actuating rod.
  13. Remove the bolts and position the front door latch aside.
  14. Disconnect the electrical connectors.
  15. Release the interior door handle cable and remove the front door latch.
  16. Position the cable cover aside.
  17. Release the conduit and the interior door handle cable.
  18. Release the locking tab and remove the front door lock actuator.
  19. To install, reverse the removal procedure and note the following:
    1. Tighten the door latch screws to 80 inch. lbs. (9 Nm).

This procedure is followed to check and fix door locks.

Hope helps.
0helpful
1answer

How do i remove the power window switches from the doors? what special tools should i use?

From 2003 Town Car Workshop Manual / SECTION 501-05: Interior Trim and Ornamentation

REMOVAL AND INSTALLATION
Procedure revision date: 01/28/2002

NOTE: LH side shown, RH side similar.

  • Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  • Remove the window switch plate.
  • Disconnect the electrical connectors.
  • CAUTION: Use care not to damage the trim panel covers. Open the screw covers.
  • Remove the screws and the assist handle.
  • Remove screws and the front door trim.
  • Disconnect the electrical connectors.
  • To install, reverse the removal procedure.

Hope helps.
0helpful
1answer

2003 Lincoln Town Car - Power window switch removal/installation

SECTION 501-05: Interior Trim and Ornamentation 2003 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/28/2002 Front Door Trim Panel adobe.gif Printable View (206 KB) Removal and Installation
NOTE: LH side shown, RH side similar.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  1. Remove the window switch plate.
    a0045307.gif
  1. Disconnect the electrical connectors.
    a0044981.gif
  1. ani_caut.gif CAUTION: Use care not to damage the trim panel covers.
    Open the screw covers.
    a0045817.gif
  1. Remove the screws and the assist handle.
    a0045818.gif
  1. Remove screws and the front door trim.
    a0045819.gif
  1. Disconnect the electrical connectors.
    a0045834.gif
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n306887&c35=wsm%2cfront%20door%20trim%20panel%2cs3g%2c501-05%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=modem&hp=n&[aqe]
10helpful
1answer

How to remove interior door panel on 2004 ford expedition?

First pop off the door open handle back plate with a screwdriver. It just snaps on. Do the same with the switch cluster plate below which also snaps in place and remove the switch harness connectors. Next pop off the small narrow cover plate under the armrest pull handle to expose 2 Torx screws. Remove these screws. Next locate a Phillips screw in a retaining cup which is located on the end of the interior door panel just above the latching mechanism and remove that. Locate two 3/8" hex head screws at the bottom of the door panel and remove those. Grab the door panel by the armrest handle and pull up to unhook it from the door. If its the driverside door, you will also have to diconnect the mirror adjustment switch connector to free the door panel.
2helpful
1answer

Removing front door panels

gently pry out the plastic insert behind the inside door handle and remove the two black screws behind. gently pry up the plastic insert covering the brass screw at the bottom of the handhold and remove. gently pry up the window switch panel from the rear, and disconnect the electrical connector by pressing down the catch, and pulling out of the socket. remove the two brass screws holding the center of the door panel that are now exposed. remove the black plastic cover in the upper most forward part of the door by gently prying. the rest of the door panel is held on using snap clips. gently pry away from the door, and work the door handle through the door handle opening in the panel as you slide the door panel up and away from the door itself.
7helpful
1answer

My 2004 Toyota Sequoia rear door will not open - the handle is broken. How do I get into the door, whith it closed, to make the necessary repairs?

Dig out the broken bits of door handle, then on the right side insert a flat head screwdriver diagonally up and fish around for the release lever.
Push up on the screwdriver handle to manipulate the release lever down and your tailgate will open.
Remove the interior panels by unbolting the 10mm bolt behind the strap and pulling off the interior pieces held on by plastic pop fasteners.
Remove the 10mm bolts around the perimeter of the interior cover plate and let it hang by the harness.
Remove the license plate.
Remove the license plate trim panel (multiple push fasteners from behind and a few 10mm around the lock)
Replace the handle.
0helpful
1answer

Avalon door panel

Below are the removal procedures for your vehicle's front inner door panel.


On models without power windows, remove the snap ring retaining window crank handle. Remove crank handle and cover plate.
Remove lower door frame bracket garnish. Using a screwdriver, remove inside door handle bezel. Remove power mirror control switch and disconnect harness connector.
Remove armrest panel. Remove 6 screws. Pry interior door panel loose from door.
Not finding what you are looking for?

65 views

Ask a Question

Usually answered in minutes!

Top Nissan Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...