1999 saab 9-5t display says radio code as far as i can read it. display needs help. but radio wont turn on at all. can you help me find out where to find this code and input it.

SOURCE: 1999 Saab 900 radio reset code

whenever the battery is removed (or car experiences any loss of power) you must type in security code for  radio (this is the case with BMWs and Volvos as well).  Go to any saab dealership and they can remove the radio and get your radio's 4 digit code, they all have one.  Yes, I have done this before ` they didn't charge me and I was in and out in ten minutes. 

SOURCE: Need to input my radio code on 2005 Honda Civic

ok your radio displays ERR , OK 3 options let it sit for an hour turned on , to reture to CODE display , or pull the radio fuse out for a minute and put it back in , returning to the CODE display , or disconnect the battery for a minute , returning to the CODE display . you got the ERR display because the code was wrong or not entered correctly , make your choice of getting the radio back to the CODE display by 1 of those 3 choices , while the radio displays CODE , use the preset buttons , if the first number of your code is 4 , then press the #1 preset button 4 time , when the first number has been input , put the 2nd number in by pressing the #2 prest button , if 2nd number of code is 8 , press the # 2 preset button 8 times till the # 8 is displayed , and so on . you see where this is giong ? when you have entered all the numbers correctly you will have you radio back . when you say you have the radio code , good luck ! were rooting for ya .

J5

SOURCE: car radio problem

I would try removing either the two fuses for the radio or disconnecting the ground on the battery for a while. When you start the car it should rest from "OFF" to "CDE" and you will be able to enter code again

mx5turbo92

• 545 Answers
• Posted on Dec 17, 2009

SOURCE: i need the mercedes benz 1999 clk 430 radio code

AR82.60-P-7502-01A Coding Radio
(MODEL all with CODE (750) Radio Becker Europa 2000 with CODE (751) Radio Becker Grand Prix 2000 with RDS)

1. If the radio is disconnected from the power supply, it is not operational when re-connected. After switching on the ignition and the radio, the readout CODE appears in the display.
2. The code number for the radio is advised to you on the enclosed CODE CARD.
3. To enter the first digit of the code number, you have to continue pressing station button 1 until the correct digit appears in the display. Adopt the same procedure for the second, third and fourth digits.
4. Once you have entered the correct code number with the station buttons 1, 2, 3, 4 and confirmed the entry with the SEEK button (press down), the readout CODE disappears. The radio can now be operated.
5. If you enter a wrong code three times, you must wait 15 minutes before making a new entry. In addition, if 9 incorrect entries are made, the radio will then not operate for 24 hours. During this time the radio and the ignition (terminal 15) must remain switched on.

1. If the radio is disconnected from the power supply, it cannot be operated by simply reconnecting. After switching on the ignition and the radio the word "CODE" appears in the display on the radio.
2. The code number for the radio is given on the enclosed CODE CARD.
3. Enter the code number with the station button, e.g. number 1, station button 1. After entering the first number the word "CODE" disappears and the number entered appears followed by 4 dashes. The next character to be entered flashes. After entering all five numbers, the first character starts flashing again. In this state the code number can be written over as frequently as desired. A correction can be made only by entering the complete code number again.
4. Confirm code number: Press TUNE, AUTO/SEEK or SC button. The radio automatically switches on and indicates the radio station or frequency stored with station button 1.
5. If an incorrect code number is entered and confirmed, the word "CODE" appears again on the display. If an incorrect code is entered three times the word "WAIT" appears on the display and the radio locks up for approx. 10 min. If the code is entered incorrectly three times again the radio locks up again for 10 min. Three more incorrect entries (a total of 9 incorrect attempts) increase the lock-up time to 60 min. Another three incorrect entries lock up the radio for another 60 min. The waiting time runs only when the radio is switched on.

SOURCE: SAAB 9-3 radio problems

You have blown bulbs on a radio panel.Need to remove the radio,useing special 4 pins tool and change blown bulbs. 2-What about the steering wheel joystick-can you change from radio to cd? If so,problem in a contacts in switch.