Cars & Trucks Logo

Related Topics:

What is the proper method to remove 2001 corvette coupe right front fender

5 Related Answers

Anonymous

  • 242 Answers
  • Posted on Nov 20, 2008

SOURCE: Right front wheel gets hot.

It sounds like a classic "hot brake", your caliper is probably stuck depressed on the rotor. You will probably need to replace the caliper and both front rotors as the one that is getting hot is probably warped. They are replaced in pairs. Get the rotors/caliper and do it yourself. It really is a simple task with minimal tools/mechanical expertise. Get a Hanyes repair manual and it will be a breeze and save you $1K.

Ad

Anonymous

  • 1 Answer
  • Posted on Mar 21, 2009

SOURCE: Remove right front fender on 2005 odyssey

NO 2 BOLTS ON TOP OF FENDER UNDER HOOD 1 BOLT BEHIND PLASTIC TRIM BY MIRROR PULL THIS PIECE BACK TOWARDS MIRROR OR IT WILL BREAK TABS OFF 1 BOLT UNDER ROCKER TRIM 1 SCREW INTO ROCKER AND 1 SCREW BEHIND PLASTIC SHROUD GOING INTO BUMPER FROM UNDER NEATH PULL BUMPER BACK SLIGHTY AND YOU WILL SEE A WHITE PLASTIC CLIP PULL BACK AND BEHIND THIS IS A BOLT REMOVE HEADLIGHT CLIP FROM FENDER AND LOSEN BOLT BY HINGE NOW FENDER SHOULD COME RIGHT OFF BOOK IS 2 HOURS TAKES 1 HOUR TO REMOVE BUT GOES ON IN ABOUT 30 NINUTES

Anonymous

  • 3533 Answers
  • Posted on Mar 21, 2009

SOURCE: need to replace my right front fender fo my 2003 hyundai tiburon

try www.autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Anonymous

  • 37 Answers
  • Posted on Apr 05, 2009

SOURCE: I am removing the right front fender on a 96 pontiac grand prix

U NEED TO TAKE YOUR FINDERWELL OUT FRIST ON THAT SIDE THIN OPEN HOOD THE BOLTS R RIGHT AT THE TOP WERE YOUR HOOD FITS THE FINDER SHOULD BEE ABOUT SIX OR SO NOTE THE FINDER WELL IS THE UNDER NEATH PART OF YOUR FENDER U MAY WONNA REMOVE YOUR PARKING LIGHT FOR THAT SIDE JUST TO MAKE SURE U DONT BRAKE IT AND JUST BELOW THE MARKER LIGHT SHOULD BEE A FENDER BRACE REMOVE IT ALSO ITS LIKE A SHORT METTEL BAR ALL BOLTS SHOULD BEE 1/2 INCH GOOD LUCK AND RATE THIS PLEASE

Anonymous

  • 1 Answer
  • Posted on Sep 12, 2009

SOURCE: trying to locate fuel pump relay for 1991 corvette- coupe

The fuel pump relay in the 1991 corvette is located under the IP on the pass side.
Open pass door, unscrew two screws under the glovebox (you will be upside down in the car), take off the fuse panel, unscrew third screw to plastic plate underneath glovebox, pull away carpet (velcro), pull down plastic plate (watch out for the wiring to the lamp), then under the glovebox you will find a number of fuses and relays if you dive in under there DEEP, prob 4 or 5 in a row, not really sure wich one, but one in the middle is the fuel relay, and they are the same (interchangable).
Take a look at --the12volt.com/relays/relays.asp--
It´s those relays we are talking about.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Will 2008 m3 wheels fit 01 e46 coupe?

Per Tire Rack, for a 2001 330ci you could use 235/35-19 front and 245/35-19 in the rear. Wider tires for the same profile increase the tire's effective diameter(think wheel well gap above the tire) and will change both the odometer and speedometer readings. Additionally, the wider tires may cause rubbing of the fender or other components while turning unless the fenders are flared out.
Caliper clearance should be checked, usually M3 uses bigger calipers than stock. While they may look cool installed, there are several disadvantages to lolwer profile tires such as harsh ride, unforgiving of potholes/speedbumps, wider width is worse for snow application (cause that floating feeling). The 2008 wheel will have the tire pressure monitoring system (TPMS) .
Both have a bolt pattern of 5-120.
0helpful
1answer

Where is the pcm located on a 2002 Chevy Cavalier?

I suggest check in right front fender. Remove wheel and front part of splash shield.
Good luck.
1helpful
1answer

HOW TO CHANGE FRONT RIGHT FENDER?

Basically you remove the hood, remove front lights, then unbolt the fender from the uni-body. reverse to put the new one on.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c

0helpful
2answers

2001 dodge stratus coupe 3.0 where to get a front bumper cover

try www.vengusa.com. they have new aftermarket parts. fenders bumper covers,etc. good prices too. hope this helps.
1helpful
1answer

Getting to the tail lights of an 89 corvette

I have a 1989 Coupe and I removed the fuel door and the fuel boot and reached in through the access. You have to have skinny arms, though. It's a tight fit. I've read where some remove the inner fender, possibly the spare tire too or remove the rear fascia. Never tried those since I have skinny arms and can reach through after removing fuel door and boot.
0helpful
1answer

How do you change a burned out front right side turn signal bulb?

YOU HAVE TO REMOVE RIGHT SIGNAL BULB FROM INSIDE THE FENDER NEXT TO FRONT WHEEL.
1helpful
1answer

ECM Location

For one i dont need your vin its a z24 which means it has a 2.4l engine it does not have an ECM it has a PCM powertrain control module, which is located for your car in the right rear corner topside of your engine bay, in 1995-2001 it is located inside the right front fender. I hope this info helps...
1helpful
1answer

Putting in a new blower motor.

Hi, First remove the radiator overflow tank behind the right fender well, you may also have to loosen and place the a/c pump aside. Jack up the pass side of the car, with a combination of below and up inside the fender well , you can remove the blower motor fasteners, then replace the motor. Advance auto parts has this assembly available with the squirrel cage included. This is not an easy job but will be very rewarding.
2helpful
1answer

Right front wheel gets hot.

It sounds like a classic "hot brake", your caliper is probably stuck depressed on the rotor. You will probably need to replace the caliper and both front rotors as the one that is getting hot is probably warped. They are replaced in pairs. Get the rotors/caliper and do it yourself. It really is a simple task with minimal tools/mechanical expertise. Get a Hanyes repair manual and it will be a breeze and save you $1K.
3helpful
1answer

Dont know location of computer

The PCM is located behind the right front fender splash shield, you wheel need to remove the right front wheel and splash shield to gain access to it.
Not finding what you are looking for?

52 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

john h

Level 3 Expert

29494 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...