SOURCE: 2000 isuzu rodeo brake problems
your master cylinder is gone. when stopped apply pedal and hold let up slightly then reapply if pedal sinks to floor master is bad.
SOURCE: reduced power light on, 2000 Isuzu Rodeo, can't go anywhere
all electrical power must come from an alternator an a good batterie to store it please ck your alternator or have it ck by an parts store clerk if the altrenator is bad (must develop 13 0r 14.5 volts output. anyting above that ,the alt is bad!) change it then ck your batterie an batterie connections terminals and all the 80 amp fuses on the fuses box nicolas
SOURCE: 2002 Saturn S-series Passlock needs to be reset
Try this first, it takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself. Good luck and hope this helps, keep me posted, be glad to help
SOURCE: 2000 isuzu rodeo trans range and leak problem at $1000?
I have a v6 2000 rodeo and the transmission contiunes to have a slip in it what should I do!! I have been having this problem since I purchased the car brand new in Oct 2000!! What should I do
SOURCE: I need to change the fuel filter on my 2000 isuzu rodeo. How?
It's located just under the driver side door, and then behind the outermost frame bar. The new one will denote which direction to install it. I recommend grabbing some rubber sheathed hose clamps from the store while you're there.
First locate the bleeder valve on the fuel rail.
It's just underneath the plastic
cover on the engine, follow the silver rail that runs across the front
and goes back on both sides, it's on the right side, just under the
left-side blue refrigerant valve cover. Open the cover (black) and be sure to have a rag under and on top of it as you use a screwdriver to release the pressure on it - just push the pin in the valve. Air will come out, then a little gas, so be ready. Replace the cover.
Open your gas cap. Now the pressure is off of both sides.
Use the clamps to close the lines going into it, in and out. Clamp them about 3 or 4 inches from the filter, to leave yourself room to work.
Remove the bolt on the mounting bracket, it will take a socket to get it, as salt and other road juices will have rusted it pretty well since the last time it was changed. Please don't try to use an adjustable wrench, unless you really want to punch the underside of your car.
Factory hose clamps, self explanatory. Vice grips are good for this.
Use the vice grips to gently wrench the hose from the filter. This will take some work, it's on there very tight from the existing pressure in the lines. just don't clamp them so tight that it might tear them. Just hand tight and wiggle back and forth.
When it comes off, gas is going to spill out, be ready. Quickly replace the filter and replace the factory hose clamps, remove yours, and remount it in the bracket.
Close your gas cap!
Start your car a few times to get the pressure back in the lines, and you're all set.
364 views
Usually answered in minutes!
×