2006 Toyota Highlander Logo

Related Topics:

J
J P br Posted on Aug 05, 2017
Be the first to answer

How do you replace the entire High Mount Lamp assembly on a 2006 Toyota Highlander? Not just the bulb, but the entire assembly.

Answer This Question

5 Related Answers

Anonymous

  • 1990 Answers
  • Posted on Jan 01, 2009

SOURCE: I want to remove and

The Mounts for these are Under the Hood and Look like Wing Nuts But Plastic. Should be around the Area that the Light Harness Plugs into the Back of the Housing

Ad

Anonymous

  • 73 Answers
  • Posted on Jan 16, 2009

SOURCE: 2006 nissan murano headlight out

Bulb can be replaced. You can buy at Walmart or your local parts store. I recommend replacing both. They are rated for the same amount of run hours and will usually fail within the same month.

You can also buy from this link.
http://www.partsgeek.com/gbproducts/YN/B18919-HEL-P8040.html?utm_source=google&utm_medium=ff&utm_term=06+2006+Nissan+Murano+Headlight+Bulb+Hella+Nissan+Headlight+Bulb&utm_content=YN&utm_campaign=PartsGeek+Google+Base

Anonymous

  • 1 Answer
  • Posted on Mar 20, 2009

SOURCE: How do I replace the bulb in the high mount stop light?

Please look at the bottom of your tail lights there is 1 flat head screw there. Take it out and you can slide tail light out. You will find the back of the bulb there. Be care when returning the assembly back in place as it slide up and then you just replace the screw.

Joseph Bonomo

  • 87 Answers
  • Posted on Mar 28, 2009

SOURCE: High mount brake light

Hi i would take it to the dealer. they are really hard to do and thay take me almost and hour.

Anonymous

  • 1129 Answers
  • Posted on Jul 14, 2009

SOURCE: 2006 Elantra; Does the entire headlight assembly

On these the bulb unscrews from the back

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Removal headlight assembly 2006 Toyota highlander
not sure if you are talking entire assembly or just bulb so covered both:


Read full answer
Jan 08, 2015 • Toyota Cars & Trucks
0helpful
2answers

How do i replace the bulb in a fog light on a toyota highlander 2002
toyota tech you need to remove plastic cover under front car to gain access very easy job
Read full answer
Oct 18, 2014 • 2002 Toyota Highlander
0helpful
1answer

I was told by a local car shop that in order to fix the High Mount Brake Lamp (brake light is out) that I would need to replace the entire unit. One year ago it cost me $172.03 to replace the entire unit....
check to see if you got two screws if you do all you need is the light bulb if you still have the old one look at it and see if the bulb can be replace without breaking anything i no you mention a year ago
Read full answer
Sep 24, 2012 • 2005 Ford Taurus
0helpful
1answer

Rear turn signal b ulb burned out - How to replace
Rear Turn Signal, Brake and Parking Lights
  1. Remove the tail light assembly screws, then the assembly.
  2. Disconnect the twist lock socket from the lens housing. NOTE: To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1?4 turn, then remove the socket with the bulb; replace the bulb if defective. Fig. 7: Remove the tail light assembly screws, then the assembly - wagon shown 86816223.jpg Fig. 8: Twist the socket counterclockwise to remove from the housing 86816225.jpg Fig. 9: This type of bulb simply can be pulled out of the socket for replacement 86816226.jpg To install:
  3. Attach the socket assemblies to the back of the lamp unit.
  4. Install the lamp assembly to the vehicle with the mounting screws.
License Plate Light
  1. Remove the lens screws.
  2. Once the lens is removed you, can access the bulb and replace if needed. To install:
  3. Install the new bulb, then attach the lens to the body of the vehicle.
Center High Mount Stop Lamp
  1. Remove the screws securing the lamp cover.
  2. Remove the mounting nuts, then unplug the electrical harness to the lamp assembly.
  3. The lamp now should come out. To install:
  4. Position the lamp assembly to the vehicle, then attach the electrical harness to the lamp.
  5. Install the mounting nut, tighten to 62 inch lbs. (7 Nm).
  6. Attach the lamp cover. Fig. 10: Exploded view of the center high mount stop lamp assembly - wagon shown 86816230.gif
    Fig. 11: Light bulb application chart for all models with non-European headlamps 86816237.gif
    Fig. 12: Light bulb application chart for Buicks with European headlamps 86816235.gif
    Fig. 13: Light bulb application chart for Oldsmobiles with European headlamps 86816236.gif
    prev.gif next.gif
Read full answer
Dec 19, 2010 • 1994 Buick Century
0helpful
1answer

Replace a brake light
COUPE The side marker lights for the SC and SC2 are part of the turn signal/parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. Rear Turn Signal, Brake and Parking Lights EXCEPT WAGON
  1. Disconnect the negative battery cable. Fig. 5: Remove the trim panel fasteners - except wagon 84196109.jpg
    Fig. 6: Carefully remove the trim panel - except wagon 84196110.jpg
    Fig. 7: Pull the lamp assembly straight back and out of the opening 84196111.jpg

  2. Remove the trim panel fasteners, then carefully remove the trim panel.
  3. Remove the 2 retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  4. Tilt the assembly downward for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  5. Installation is the reverse of removal. Fig. 8: Tilt the assembly downward for access to the sockets 84196112.jpg
    Fig. 9: Twist and remove the socket and bulb from the lamp assembly 84196113.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Remove the retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  3. Tilt the assembly for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  4. Installation is the reverse of removal. Fig. 10: Exploded view of the tail lamp assembly - wagon 84196114.gif
High-Mount Brake Light EXCEPT WAGON
  1. Disconnect the negative battery cable.
  2. Open the trunk for access to the lamps.
  3. Locate the bulbs at the rear underside of the trunk lid. Remove the bulb(s) by twisting, then pulling straight out.
  4. Installation is the reverse of the removal. Fig. 11: Remove the high-mount brake light by twisting its socket 1?4 turn counterclockwise - except wagon 84196115.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Raise the liftgate, then remove the wedge blocks from each side of the liftgate assembly.
  3. Remove the lower fasteners from the liftgate lower trim panel, by pushing in the center of each pin approximately 1?8 in. until it clicks, then remove the fastener.
  4. Insert a screwdriver or small prybar into the hole in the lower trim panel (located near the wiper pivot on the pivot hump) so that the tool sits on top of the pivot. Lift up on the tool handle to disengage the trim panel upper clips, then remove the lower trim panel from the vehicle.
  5. Unplug the high-mount brake light wiring harness.
  6. Remove the brake light fasteners, then remove the lamp assembly from the liftgate.
  7. To remove the bulb(s), push slightly on the top edge of the lens and rotate it away from the housing. Remove the bulb(s) from the housing. To install:
  8. In order to prevent the possibility of water leaks into the liftgate, inspect the lamp gasket for damage and replace, if necessary.
  9. If removed, install the bulb(s) by inserting the bottom edge of the lens into the housing and snapping it into place.
  10. Position the lamp into the liftgate and tighten the fasteners to 35 inch lbs. (4 Nm).
  11. Connect the wiring harness to the lamp assembly.
  12. Align the upper clips on the lower trim panel to the liftgate slots, then install the panel by pushing at the clip locations.
  13. Reset the trim panel push-in fasteners by spreading the center pin tabs and moving the pin so that it sits approximately 1?4 in. out of the fastener. Insert the fasteners into the bottom of the trim panel and push the center pin until flush.
  14. Install the liftgate wedge blocks.
  15. Connect the negative battery cable and check for proper lamp operation. Fig. 12: Removing the liftgate lower trim panel assembly - wagon 84196116.gif
    Fig. 13: Exploded view of the high-mount brake light bulb and lens assembly - wagon 84196117.gif
Read full answer
Nov 04, 2010 • 1998 Saturn SL
0helpful
1answer

I need to replace rear tail light bulbs on 1996 Saturn SL1
COUPE The side marker lights for the SC and SC2 are part of the turn signal/parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. Rear Turn Signal, Brake and Parking Lights EXCEPT WAGON
  1. Disconnect the negative battery cable. Fig. 5: Remove the trim panel fasteners - except wagon 84196109.jpg
    Fig. 6: Carefully remove the trim panel - except wagon 84196110.jpg
    Fig. 7: Pull the lamp assembly straight back and out of the opening 84196111.jpg

  2. Remove the trim panel fasteners, then carefully remove the trim panel.
  3. Remove the 2 retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  4. Tilt the assembly downward for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  5. Installation is the reverse of removal. Fig. 8: Tilt the assembly downward for access to the sockets 84196112.jpg
    Fig. 9: Twist and remove the socket and bulb from the lamp assembly 84196113.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Remove the retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  3. Tilt the assembly for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  4. Installation is the reverse of removal. Fig. 10: Exploded view of the tail lamp assembly - wagon 84196114.gif
High-Mount Brake Light EXCEPT WAGON
  1. Disconnect the negative battery cable.
  2. Open the trunk for access to the lamps.
  3. Locate the bulbs at the rear underside of the trunk lid. Remove the bulb(s) by twisting, then pulling straight out.
  4. Installation is the reverse of the removal. Fig. 11: Remove the high-mount brake light by twisting its socket 1?4 turn counterclockwise - except wagon 84196115.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Raise the liftgate, then remove the wedge blocks from each side of the liftgate assembly.
  3. Remove the lower fasteners from the liftgate lower trim panel, by pushing in the center of each pin approximately 1?8 in. until it clicks, then remove the fastener.
  4. Insert a screwdriver or small prybar into the hole in the lower trim panel (located near the wiper pivot on the pivot hump) so that the tool sits on top of the pivot. Lift up on the tool handle to disengage the trim panel upper clips, then remove the lower trim panel from the vehicle.
  5. Unplug the high-mount brake light wiring harness.
  6. Remove the brake light fasteners, then remove the lamp assembly from the liftgate.
  7. To remove the bulb(s), push slightly on the top edge of the lens and rotate it away from the housing. Remove the bulb(s) from the housing. To install:
  8. In order to prevent the possibility of water leaks into the liftgate, inspect the lamp gasket for damage and replace, if necessary.
  9. If removed, install the bulb(s) by inserting the bottom edge of the lens into the housing and snapping it into place.
  10. Position the lamp into the liftgate and tighten the fasteners to 35 inch lbs. (4 Nm).
  11. Connect the wiring harness to the lamp assembly.
  12. Align the upper clips on the lower trim panel to the liftgate slots, then install the panel by pushing at the clip locations.
  13. Reset the trim panel push-in fasteners by spreading the center pin tabs and moving the pin so that it sits approximately 1?4 in. out of the fastener. Insert the fasteners into the bottom of the trim panel and push the center pin until flush.
  14. Install the liftgate wedge blocks.
  15. Connect the negative battery cable and check for proper lamp operation. Fig. 12: Removing the liftgate lower trim panel assembly - wagon 84196116.gif
    Fig. 13: Exploded view of the high-mount brake light bulb and lens assembly - wagon 84196117.gif
Reverse Light EXCEPT 1991-96 COUPE For the Saturn wagons and sedans, the reverse lamp is part of the rear turn signal, brake and parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. 1991-96 COUPE
  1. Disconnect the negative battery cable.
  2. Reach behind the bumper bar and disconnect the harness and socket from the reverse lamp. Remove the bulb from the socket.
  3. If necessary, unfasten the retaining nuts and remove the lamp from the bumper bar.
  4. Installation is the reverse of the removal. Fig. 14: Exploded view of the reverse lamp mounting - 1991-96 coupe 84196118.gif
Read full answer
Oct 23, 2010 • 1996 Saturn SL
1helpful
1answer

Need to replace stop light
Tail Lamp Assembly Removal & Installation To Remove:
Tail lamp assembly removal and installation gm-06-00-1645.gif

  1. Remove the tail lamp assembly retaining screws from the body.
  2. Release the locking pins by pulling the assembly directly rearward.
  3. Disconnect the tail lamp assembly connector.
  4. Remove the tail lamp circuit board from the assembly.
To Install:
  1. Install the tail lamp circuit board into the assembly.
  2. Connect the tail lamp assembly connector.
  3. Push the assembly directly forward into the opening to engage the locking pins.
  4. Install the tail lamp assembly retaining screws into the body. Torque the screws to 17 in-lb (1.9 Nm).
High Mount Stop Lamp Removal & Installation To Remove:
CAUTION
Raising the liftgate with the liftgate window open can damage the high mount stop lamp, liftgate hinges, and the liftgate window.
  1. Raise the liftgate.
  2. Lower the rear of the headliner by removing the rear headliner pins.
  3. Disconnect the high mount stop lamp connector.
  4. Remove the high mount stop lamp grommet from the body.
  5. Lower the liftgate.
  6. Open the liftgate window.
  7. Remove the high mount stop lamp retaining screws from the liftgate window molding.
  8. Remove the high mount stop lamp from the vehicle.
To Install:
  1. Place the high mount stop lamp onto the vehicle.
  2. Install the high mount stop lamp retaining screws into the liftgate window molding. Torque the screws to 22 in-lb (2.5 Nm).
  3. Close the liftgate window.
  4. Lift the liftgate.
  5. Install the high mount stop lamp grommet into the body.
  6. Connect the high mount stop lamp connector.
  7. Install the rear of the headliner by inserting the retaining pins.
prev.gif next.gif
Read full answer
Oct 18, 2010 • 2004 GMC Envoy
4helpful
1answer

How do you replace the high mount stop light bulb on the 2004 highlander?
Did my 2005 highlander. You replace from the inside. On the inside of the rear hatch, the top center plastic molding gentle snaps off. You twist out the bulb holder and replace with one #921 bulb
Read full answer
Aug 18, 2010 • 2004 Toyota Highlander
5helpful
2answers

2002 Toyota highlander passenger brake light not working
RE: 2002 Toyota Highlander 2.4cyl. 4X4 Base Model

I am a Certified Technician and have basic knowledge with electronics in electrical wiring. I searched the web and discovered this is a common problem.

I fixed the problem and it was a simple procedure... The problem is with the reverse light socket at the side with no brake light. This socket functions as a hub to direct current to the brake bulbs.

Remove reverse light socket and re-seat bulb. Check for loose or broken prongs. Replace if necessary.

Swap the reverse socket with the other side.
Read full answer
Oct 06, 2009 • 2002 Toyota Highlander
0helpful
1answer

2002 Chevy Tahoe: Replacing Bulbs in Rear High Mount Stop Light?
Yes you can do this your self. When you open the back hatch their should be a way to take out the whole back light system, which then you can replace each individual light.
Read full answer
Jul 01, 2009 • 2002 Chevrolet Tahoe
Not finding what you are looking for?

View Most Popular

2006 Highlander

  • Cars & Trucks

Related Question

Removal headlight assembly 2006 Toyota highlander

  • Toyota Cars & Trucks

185 views

Ask a Question

Usually answered in minutes!

Popular Questions

My toyota Highlander is showing CHECK VSC light

2008 Toyota Highlander

Why wont interior lights will not turn off on toyota highlander

2014 Toyota Highlander

CODE C1201 ENGINE CONTROL SYSTEM MALFUNCTION

2005 Toyota Highlander

Toyota 04 Highlander Temp Control Problem

2004 Toyota Highlander

What does htd catalyst n/a mean

2004 Toyota Highlander

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Toyota Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. 2006 Highlander Manual

2006 Highlander

Loading...