Can anyone supply me with Torque specs for 2008 Chevy Tahoe 4WD, 5.3 L: Front & Rear Brake: Caliper bolts,bracket bolts, fluid line bolts front & rear,Exhaust Flange bolt & Wheel lug torque

Tight enough to compress the sealing washer. Not enough to strip the threads. Some parts don't need a torque setting.

33 foot pounds is the answer.

Torque Specs for Brake Caliper Bolts - Chevy HHR Network

https://www.chevyhhr.net > forums > torque-specs-brak...

Apr. 23, 2017 - Brake hose-to-brake caliper bolt to the brake caliper, tighten the bolt to 44 N·m (33 lb ft). Been away on vacation, thanks ChevyMgr for the info!! ChevyMgr's ... Need Torque spec's for front brake job - Chevy HHR Network
Oct. 1, 2008
Front brake caliper bolts on 2010 1LT - Chevy HHR Network
Apr. 23, 2017
Tightening Torque Values for Common Maintenance Items
Apr. 23, 2017
Turbo coolant banjo bolts torque specs - Chevy HHR Network
Dec. 24, 2018
More results from www.chevyhhr.net

Those are Brake Caliper Bracket Bolts - Front
175 N?·m
129 lb ft
Brake Caliper Guide Pin Bolts - Front
Tighten the guide pin bolt closest to the bleed valve first.
64 N?·m
47 lb ft

1. Torque Specs For F250 Caliper Bolts - Diesel Forum - TheDieselStop.com

   www.thedieselstop.com > ... > 1999-2007 General Questions Jan 13, 2009 - 3 posts - ‎1 author
   Does any one know what the caliper bolts torque specs are? ... Disc brake caliper pin bolts - Excursion, F-250/F-350 with Ford and Dana axle ... Torque specs for front brakes
   5 posts
   Mar 12, 2009
   05 F250 brake torque specs please
   6 posts
   Aug 22, 2007
   Brake caliper torque specs
   5 posts
   Jul 14, 2007
   Front brake Caliper Bolt Torque
   6 posts
   Apr 25, 2005
   More results from www.thedieselstop.com

First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

Brake Pads Removal & Installation Front

To Remove:

1. Drain brake fluid to ½ full level in reservoir.
2. Remove the front wheels.
   
   
3. Remove the front brake caliper assembly.
4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
5. Remove the wear indicator from each of the 2 brake pads.

To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.

1. Using a large C clamp or equivalent press piston into the caliper.
2. Apply disc brake grease to the inside of each anti-squeal shim.
3. Install the anti-squeal shims on each pad.
4. Install the pad wear indicator clip to the pads.
5. Install the pads with the pad wear indicator plate facing upward.
6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
7. Install the front wheels.
8. Fill the master cylinder with new clean brake fluid.
9. Pump the brake pedal several times to seat the brake pads.

Rear TMC made rear brake components

TMMK made rear brake components

To Remove:

1. Drain the brake fluid to ½ full level in reservoir.
2. Remove the rear wheels.
3. Remove the caliper slide pins.
4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
5. Remove the rear brake calipers.
6. Remove the 2 brake pads with the anti-squeal shims.
7. Remove the anti-squeal shims and pad wear indicators from brake pads.

To Install:

1. Using a large C clamp or equivalent press the piston into the caliper.
2. Coat both sides of the outer anti-squeal shim with pad grease.
3. Install anti-squeal shims to each pad.
4. Install wear indicators on the 2 brake pads.
5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
7. Fill the master cylinder with new clean brake fluid.
8. Pump the brake pedal several times to seat the brake pads.
9. Install the rear wheels.

Brake Rotor Removal & Installation Front To Remove:

1. Remove the front wheels.
2. Remove the front brake caliper assembly.
3. Remove the front brake pads.
4. Remove the 2 bolts and caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the front wheel disc.

To Install:

1. Align the match marks and install the front disc.
2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the front wheel.

Rear To Remove:

1. Remove the rear wheels.
2. Remove the brake caliper assembly.
3. Remove the brake pads.
4. Remove the 2 bolts and the caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the rear disc.

To Install:

1. Align the match marks and install the rear disc.
2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
   • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
   • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the rear wheel

IF this helps, don't forget to vote.

Removal & Installation


CAUTION Dust and dirt accumulating on brake parts during normal use may contain asbestos fibers from production or aftermarket brake linings. Breathing excessive concentrations of asbestos fibers can cause serious bodily harm. Exercise care when servicing brake parts. Do not sand or grind brake lining unless equipment used is designed to contain the dust residue. Do not clean brake parts with compressed air or by dry brushing. Cleaning should be done by dampening the brake components with a fine mist of water, then wiping the brake components clean with a dampened cloth. Dispose of cloth and all residue containing asbestos fibers in an impermeable container with the appropriate label. Follow practices prescribed by the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA) for the handling, processing, and disposing of dust or debris that may contain asbestos fibers.

1. Before servicing the vehicle, refer to the Precautions Section.
2. Raise and safely support the vehicle. Remove the front wheels.
3. Remove some brake fluid from the master cylinder reservoir.
4. Disconnect and plug the brake fluid line from the caliper.
5. Remove the brake caliper mounting bolt and guide bolt and remove the caliper from the mount. The brackets can be removed for additional work space.
6. Remove the brake pads and clips from the caliper. Inspect the brake pads for wear; replace them, if necessary.
   
   

   Fig. Front caliper and related parts
   

To install:

1. Install the brake pads and clips onto the caliper.
2. If the caliper bracket was removed, tighten the bolts to 115 ft. lbs. (155 Nm).
3. Install the caliper on the mounting bracket. Torque the caliper-to-mounting bracket bolts to 33 ft. lbs. (45 Nm).
4. Connect the fluid line to the caliper using new washers. Torque the brake line banjo fitting to 26 ft. lbs. (35 Nm).
   WARNING Be sure the hook end of the flexible brake line is positioned in the anti-rotation cavity.
   
5. Refill the master cylinder reservoir and bleed the brake system.
6. Install the front wheels and lower the vehicle.

Back to Top

2010-2017 Equinox

FRONT brake caliper BRACKET bolts Torque is 140 FT/LB and Caliper to the bracket is only 20 FT/LB.

REAR brake caliper BRACKET bolts Torque is 92 FT/LB and Caliper to the bracket is 20 FT/LB.

Remember rear bracket torque is different so don't forget as many DIY mechs snap that rear bracket bolt.

Use Thread Lock on caliper BRACKET Bolts.

Caliper bolt 25 ft lbs/ caliper bracket bolt 79.6 ft lbs

Tighten the 2 brake caliper mounting bolts to 108 Nm (80 ft. lbs.) . Caliper Mounting Bracket to Knuckle, Front (15 series) 175 Nm (129 ft. lbs.) Caliper Mounting Bracket to Knuckle, Front (25/35 series) 300 Nm (221 ft. lbs.) Brake Caliper Mounting Bolt Rear (15 series) 42 Nm (31 ft. lbs.) Brake Caliper Mounting Bolt Rear (25/35 series) 108 Nm (80 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JC5/JH5) 200 Nm (148 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH6) 165 Nm (122 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH7) 300 Nm (221 ft. lbs.) Caliper Mounting Bracket Bolt Rear (NYS) 200 Nm (148 ft. lbs.)
hope this helps