1996 Ford Explorer Logo

Related Topics:

Stephen Kent Posted on Jun 23, 2017

Gem wiring on a 1996 ford explorer - 1996 Ford Explorer

5 Related Answers

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Sep 29, 2008

SOURCE: wiring diagram 1996 ford explorer premium sound radio f57f-19b165-ag

Here it is.

1996 Ford Explorer Car Stereo Radio Wiring Diagram
Car Radio Constant 12v+ Wire: Green/Violet
Car Radio Switched 12v+ Wire: Yellow/Black
Car Radio Ground Wire: Black/Light Green
Car Radio Illumination Wire: Light Blue/Red
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger: Orange/Blue
Car Stereo Amp Trigger Wire: Blue (If Equipped)
Car Stereo Amplifier Location: N/A
Front Speakers Size: N/A
Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Orange/Light Green
Left Front Speaker Negative Wire (-): Light Blue/White
Right Front Speaker Positive Wire (+): White/Light Green
Right Front Speaker Negative Wire (-): Dark Green/Orange
Rear Speakers Size: N/A
Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Gray/Light Blue
Left Rear Speaker Negative Wire (-): Tan/Yellow
Right Rear Speaker Positive Wire (+): Orange/Red
Right Rear Speaker Negative Wire (-): Brown/Pink
-->

Ad
Breed1956

Berlyn Reed

  • 492 Answers
  • Posted on Mar 01, 2011

SOURCE: can you take a 1999

IF THE PLUGS MATCH UP YOU'RE GOOD TO GO! IF NOT, YOU MAY NEED A WIRING DIAGRAM, OR PLUG ADAPTER!

Anonymous

  • 65 Answers
  • Posted on May 05, 2011

SOURCE: I have residual current draw on 1996 Ford

When checking a draw you have to wait to check till all modules have powered down including Gem module. This can take up to 30 min. Specs are 50 ma draw. To check get you a test light take off the postitive cable, " you can also use a meter", now you have to put the light in series withe the battery and cable. Clamp one side of test light to battery cable the other side to battery post WITH CABLE OFF THE WHOLE TIME. Now if you open doors turn any switches you will have to restart your 30min. then you can check and see if unplugging module, if that fixed problem. what we do is open the doors before, then take a screw driver and close the door latch so that you can get in and out of the car without turning something on

cansmo

Reynaldo Andico

  • 2431 Answers
  • Posted on Nov 26, 2012

SOURCE: Can you put a 1996 gem module into a 1998 ford explorer

Yes you can and if that GEM module doesnt work the 4X4 will flash or if you dont have the 4x4 your door lock controls wont operate

Testimonial: "Thanks so much for the info!"

Jeff Armer

  • 15575 Answers
  • Posted on Jan 19, 2015

SOURCE: 1996 ford explorer headlamp wiring

You can go to www.bbbind.com an get free wiring diagrams an TSB's Technical Service Bulletins Click on Technical Information then Technical Service Bulletins & Wiring Diagrams - Then you will see this END-USER LICENSE AGREEMENT , go to bottom of the page an click on I Agree next page you'll see this ..

  • TSBs
  • Wiring Diagrams
  • Search Technical Service Bulletins

    Year 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997 1996 1995 1994 1993 1992 1991 1990 1989 1988 1987 1986 1985 1984 1983 1982 1981 1980 Make Model System Subsystem


    ' Reset
    Powered by Longwood enter your vehicle info

    Ad

    Add Your Answer

    ×

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    0helpful
    2answers

    1998 Ford Explorer. Where is starting solenoid located on it please?

    Check your fuse boxes and the fusible link in the wiring harness. If you've lost power to the engine computer, bypassing the ignition switch won't help you.
    1helpful
    1answer

    Where is the body control module located on a 2002 Ford explorer XLT

    It's called a GEM - generic electronic module .It is located behind center of the instrument panel .
    SECTION 419-10: Multifunction Electronic Modules 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 10/07/2004 Module - Generic Electronic (GEM)/Central Timer (CTM) Removal
    1. CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. Depower the supplemental restraint system (SRS). For additional information, refer to Section 501-20B .
    1. Remove the audio unit. For additional information, refer to Section 415-01 .
    1. Remove the center instrument panel finish panel.
      1. Remove the screws.
      1. Remove the center instrument panel finish panel.
      • Disconnect the electrical connectors.
    1. Remove the GEM/CTM.
      1. Remove the screw.
      1. Disconnect the four connectors from the GEM/CTM.
      1. Remove the GEM/CTM.
    0helpful
    1answer

    Location of the speed sensors on my 1999 ford explorer

    Vehicle Speed Signal
    The vehicle speed signal is generated by the rear anti-lock brake sensor and sent to the 4-wheel anti-lock brake system (4WABS) module. The 4WABS module sends the vehicle speed signal via circuit 679 (GY/BK) to all systems which require a vehicle speed signal input.
    Speedometer
    The electronic speedometer receives a speed signal from the 4WABS module.
    GEM/CTM Diagnostic Trouble Code (DTC) Index
    GEM/CTM Diagnostic Trouble Code (DTC) Index DTC Description DTC Caused By Action P0500 Vehicle Speed Signal Circuit Failure GEM REFER to Section 308-07A . Take your vehicle an have it diagnosed , before you buy parts you don't need . Just a suggestion , could be a wiring problem , the speedometer gauge , computer etc...
    1helpful
    1answer

    Can you put a 1996 gem module into a 1998 ford explorer

    Yes you can and if that GEM module doesnt work the 4X4 will flash or if you dont have the 4x4 your door lock controls wont operate
    0helpful
    1answer

    Ford Explorer wipers, power windows, doom lights won't work

    Are u assuming the GEM module is at fault ? Did you or your local auto electrician check for DTC'S - diagnostic trouble codes?
    GEM/CTM Wiggle Test Diagnostic Trouble Code (DTC) Index DTC Description DTC Caused By B1317 Battery Voltage HIGH GEM/CTM B1318 Battery Voltage Low GEM/CTM B1322 Driver Door Ajar Circuit Short to Ground GEM/CTM B1330 Passenger Door Ajar Short to Ground GEM/CTM B1352 Ignition Key-In Circuit Failure GEM/CTM B1410 Driver Power Window Motor Circuit Failure GEM B1438 Wiper Mode Select Switch Circuit Failure GEM/CTM B1441 Wiper Mode Select Switch Short to Ground GEM/CTM B1446 Wiper Park Sense Circuit Failure GEM/CTM B1450 Wiper/Wash Interval Delay Switch Input Circuit Failure GEM/CTM B1453 Wiper/Wash Interval Delay Switch Input Short to Ground GEM/CTM B1462 Seat Belt Switch Circuit Failure GEM/CTM B1577 Park Lamp Input Circuit Short to Battery GEM/CTM B1610 Illuminated Entry Input (From RAP Module) Circuit Short to Ground GEM/CTM
    Did you an your auto electrican check power an grounds for the GEM ? Voltage drop testing ? . Did you check power an ground circuits for the affected systems . Working when they want sounds more like a loose connection somewhere .
    ECM Inputs and Outputs Diagnosis
    Symptom Chart
    Symptom Chart Condition Possible Sources Action
    • The Wipers Are Inoperative
    • CJB Fuse 16 (30A).
    • Circuitry.
    • GEM/CTM.
    • Multi-function switch (13K359).
    • Wiper run/park relay.
    • Wiper HI/LO relay.
    • Wiper motor.
    • DTC B1431.
    • DTC B1432.
    • DTC B1438.
    • DTC B1450.
    • DTC B1840.
    • GO to Pinpoint Test A .

    Plus looking at GEM scan data on a factory scan tool .Too many people miss diagnose these system's because they don't have a clue .
    1helpful
    1answer

    I have residual current draw on 1996 Ford Explorer. I traced it to fuse #25 (Speedometer and Gem System). Which is most likely? Can I (with battery disconnected) disconnect Gem, then reconnect battery...

    When checking a draw you have to wait to check till all modules have powered down including Gem module. This can take up to 30 min. Specs are 50 ma draw. To check get you a test light take off the postitive cable, " you can also use a meter", now you have to put the light in series withe the battery and cable. Clamp one side of test light to battery cable the other side to battery post WITH CABLE OFF THE WHOLE TIME. Now if you open doors turn any switches you will have to restart your 30min. then you can check and see if unplugging module, if that fixed problem. what we do is open the doors before, then take a screw driver and close the door latch so that you can get in and out of the car without turning something on
    0helpful
    1answer

    Can you take a 1999 ford explorer cd player and use it in the 1996 ford explorer wire harness?

    IF THE PLUGS MATCH UP YOU'RE GOOD TO GO! IF NOT, YOU MAY NEED A WIRING DIAGRAM, OR PLUG ADAPTER!
    0helpful
    1answer

    99 explorer sport. Wiring from the body control module

    There are several different wires, colors being blk/w, grn/lt blu, and pnk/wht. If you are having problems with the seat belt staying on, then prob going to be the GEM (generic electronic module).
    Not finding what you are looking for?

    1,112 views

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    ZJ Limited
    ZJ Limited

    Level 3 Expert

    17989 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    15088 Answers

    xxxxxx xxx

    Level 3 Expert

    5117 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...