Cars & Trucks Logo

Related Topics:

b
b rex Posted on Jun 06, 2017

Trailblazer: normal operation key turned slightly and released and engine turns. currently nee to hold key to engage. also when this happens, fuel gauge shows empty. ignition/sender same circuit?

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Jan 02, 2009

SOURCE: key stuck in ignition of Trailblazer.

There is a small 1/4'' oblong cover plate on the underside of the stearing column. Pop this out and there is a button you push in ( like the Crysler key relase) and this will allow you to remove the key.

Ad
emissionwiz

Marvin

  • 85242 Answers
  • Posted on Jan 27, 2009

SOURCE: 1994 cavalier ignition turn over problems

sounds like u need to replace the ignition switch.

alicantecoli

Colin Stickland

  • 22516 Answers
  • Posted on Apr 12, 2009

SOURCE: 1990 mercedes 300D (diesel)will not shut off

change the switch in the top back of the injector pump ,it has one wire running to it and should be at the back of the pump where the fuel line goes into pump housing

Testimonial: "yes thank you, PN W0133-1619965 (shut off valve) the one i used cold be found here. http://www.partsgeek.com/catalog/1990/mercedes/300d/diesel_injection/shut_off_valve.html"

Anonymous

  • 1 Answer
  • Posted on Aug 28, 2009

SOURCE: 2006 Chevy Trailblazer fuel gauge stays on empty

It requires a new fuel tank sensor that is $600 for the part.

Anonymous

  • 1 Answer
  • Posted on Sep 21, 2009

SOURCE: 2004 Chrysler Pacifica Fluctuating Fuel Gauge Indicator

Hello, the answer to solve this problem is to take it to your nearest chrysler dealer and have them re-flash the updates to the ecu....since 2004, chrysler has had about 4-5 new updates since the date they were manufactured....you need to have the update that followed from your date of man. on your vehicle....They attempted to flash mine to the latest update and didnt work, turns out that they need the re-flash from back when...in order to get the gauage to stop fluctuating.....Hope this helps!!

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Pt cruiser wont start. checked battery, starter , releighs and ignition, and they seem fine. no codes come up when turning the key 3 times

To do self diag on a pt u need to start with ignition off. Hold trip button in for the odometer keeping trip button held down turn ignition key to run then release trip. This will also run a self test on instrument cluster. Codes will be displayed in the odometer at the end of test
1helpful
1answer

When I turn key to start my 2004 Titan I am getting a click on right hand passenger side dash area instead of starter engaging with increasing frequency. Autozone found no codes and battery, starter,

Thats normally a sign of bad connection on battery terminals friend.

Try undoing them and taking them apart to clean up the battery posts and cable connectors then reconnect tightly.

What happens is the bad connection wont let a LARGE current throgh, So when you turn the key, all you are hearing is the little solenoid trying to send large current to the starter motor which is not happening.

It is a simple and VERY cheap job.
0helpful
3answers

Motor turns over normally when i turn the key but will not catch and run

When this happens have a can of spray starting fluid on hand, spray it into the engine air intake, if the engine starts you may have a failing electric fuel pump
1helpful
1answer

I have a 96 pontiac grand am that doesnt start all the time

Starting Problem # 1: Engine Won't Crank At All

Scenario: You turn the key, but nothing happens: And by nothing, we mean there is no dash light, no sound, nada. The first thing you should do in this case is to pop the hood and check the battery. Either the battery is completely dead or there's a wiring problem in the starting system. Try jump-starting the battery. If that doesn't work, you'll probably have to call for assistance.

Scenario: When you turn the key, you hear a rapid clicking sound, and the dash lights dim. This is your classic low-battery symptom. Jump-starting the battery should get the engine to start.However, if you keep experiencing this problem, you could have a bad battery or alternator, or it could be some­thing as simple as a loose alternator belt. Take your car to a mechanic just as soon as you can.

Scenario: When you turn the key, the lights on the dash come on, but you don't hear anything. Make sure you have the shift selector all the way in park. Move it out of park and then back, or try starting it with the shifter in neutral. If your car has a manual transmission, make sure you have the clutch pressed all the way to the floor. If that doesn't help, you can try jump-starting the battery, but it probably won't work. There's a good chance your car has a bad starter or a problem in the starting circuit. That could mean a prob­lem in the ignition switch, neutral safety switch or starter sole­noid.

Scenario: The dash lights come on when you turn the key, and then go right out, and the engine doesn't crank when you turn the key to start, But, the lights slowly come back on when you release the key. This is another classic: the bad battery connection. When you turn the key to start, the starter pulls so much current that it breaks the connection. Then, when you release the key, the connection slowly comes back. The connection provides enough power to turn the dash lights on, but not enough to crank the starter. Cleaning and tightening the battery terminals may fix this prob­lem.

Scenario: When you turn the key, you hear a single, hard clunk. Turn the headlights on and try again. Do the lights dim slightly when you turn the key? If so, you probably have a bad starter or a seized engine. If the headlights don't dim at all, or just barely dim, there may be a connection problem between the starter solenoid and the starter itself.

Scenario: When you turn the key, you hear a loud, scraping or grinding sound like metal on metal. The starter drive is bad, or the ring gear on the flywheel damaged, or both. You may get the starter to engage if you try turning the key a couple of times, but let go of the key right away if you hear the noise again. If the car does start, you should drive it right over to local repair shop and have the problem fixed.

Starting Problem #2: Engine Cranks but It Won't Start

Scenario: The engine seems to crank normally, but the engine doesn't even sound as if it's trying to start. Is there gas in the tank? Gas gauges are notoriously inaccurate. If you have to move your head to one side to get the needle to move off empty, try adding some gas to the tank.

Scenario: When you first turn the key on, you don't hear the fuel pump run. In cars with electronic fuel injection, you should hear a light hum a few seconds from around the fuel tank. That's the electric fuel pump running. If you don't hear the fuel pump run for a couple seconds when you first turn the key on, try cranking the engine until the oil light goes out. That may start the pump running and allow the engine to start.

Scenario: The engine cranks normally, and it sounds like it wants to start, but it won't. You may have flooded the engine. Hold the gas floor and try again. (Let the gas pedal up when it finally starts). If it's raining out, the ignition system may be wet.

Scenario: The engine cranks unevenly in a repetitive-sounding pattern. You may have a bad timing chain or timing belt. Call a tow truck and have it towed to the repair shop.


Starting Problem # 3: Engine Starts but It Shuts Off

Scenario: The engine starts right up, but shuts off as soon as you release the key. This is the classic symptom of a bad ignition switch. A new switch should fix it.

Scenario: The engine starts and runs, but when you put the transmission in gear, the car lurches and the engine shuts off. The converter clutch in the transmission torque converter probably is engaging when it shouldn't. On some cars, you can bypass this by disconnecting the torque converter clutch solenoid; but unless you know which wire to pull, forget about it. Call for assistance.

Scenario: The engine starts and runs, but seems to idle slowly and stalls when you come to a stop. This probably is a fast idle problem. When the engine is cold, it's supposed to idle a little faster than normal to keep the engine running. You may be able to drive using two feet until the engine warms up: one on the gas to hold the idle up a little and the other for the brake. However, don't keep driving it this way. Take your car to your repair shop just as soon as you

0helpful
2answers

My car turns over good, acts like it might turn on then continues to turn. I figure it might be fuel filter since low fuel light had come on.Or could it be th fuel pump got hot and is not working properly?

common problem is turning car off with engine not reaching normal operating temp and floods engine. try this. DE-CHOKING PROCEDURE WHEN ENGINE CRANKS BUT DOES NOT START
If the engine does not start, try the following procedure to start the engine using the de-choke mode.
Failure to do so may aggravate the no start condition.
1. Depress and hold the accelerator pedal to the floor and crank the engine for 7-8 seconds. (This will clean out any unburned fuel from the combustion chamber)
2. Release the ignition key to stop cranking.
3. Release the accelerator pedal and start the engine. If the engine starts while performing Step 1 the engine will rev up. Immediately release the ignition key to stop cranking and remove your foot from the accelerator pedal.
^ Do not keep holding the ignition switch in the START position over 10 seconds if the engine does not start. This may result in a weakened or dead battery.
^ Avoid racing the engine or sudden take off right after starting the engine.
^ If the engine still fails to start following the De-choking procedure, have your vehicle inspected by your Mazda Dealer.

for your info there is a recall for this problem. contact mazda.
0helpful
1answer

Sometimes on a cold start, I turn the key and nothing happens, just a click. Radio and lights come on as normal, but engine does not start. After waiting a few seconds with key on but not attempting to...

Engine is difficult to start when cold
  1. Check the battery condition, battery state of charge and starter motor current draw. Replace the battery if marginal and the starter motor if the current draw is beyond specification.
  2. Check the battery cable condition. Clean the battery terminals and replace corroded or damaged cables.
  3. Check the fuel system for proper operation. A fuel pump with insufficient fuel pressure or clogged injectors should be replaced.
  4. Check the engine's tune-up status. Note the tune-up specifications and check for items such as severely worn spark plugs; adjust or replace as needed. On vehicles with manually adjusted valve clearances, check for tight valves and adjust to specification.
  5. Check for a failed coolant temperature sensor, and replace if out of specification.
  6. heck the operation of the engine management systems for fuel and ignition; repair or replace failed components as necessary.
0helpful
1answer

Installed a new ignition (key) now when i turn key to start i get no power

Hi. There are things to be check for no starting problem. When you turn the key to sart position, did you hear the engine roaring? if there is no roaring sound you might want to check first with your starter. If you have a helper, you can test the connection by holding a circuit tester lead on the wire that engages the starter. This is the smaller of the two wires connected to the starter. Be sure no part of your body is near the moving parts of the engine - it could still start at any time! Have a friend turn the key and check the current. If you're getting current to the starter but it ain't spinning, it needs replacement.

If your starter spins freely when you turn the key, the problem lies elsewhere. Now you begin to check the other systems that could keep it from firing up. Next to check is the fuel pump. To check your fuel pump, you can do a fuel system pressure test - if you have the equipment. Since most of us don't have that type of thing, we'll first check the electrical connections. Test the positive side of the fuel pump for current with a circuit tester. Be sure the key is in the "On" position. If there's current, move on to the next step. If not, you should check the fuse. If the fuse is good, your problem is the fuel pump relay. If the fuel pump is working properly and fuel is still not reaching the engine, the problem could be a clogged fuel filter. You should be replacing your fuel filter every 12,000 miles or so anyway, so if you suspect it could be clogged, go ahead and replace it.

0helpful
1answer

I don't here a humming when key is turned on. Electric fuel pump ?? When I pump gas pedal it some times starts after it sits a while.

Could be a fuel pump although they normally only hum very briefly and change to a clicking sound that means they are maintaining fuel line pressure that was built up quickly when the ignition is turned on.
BTW; pumping the gas pedal is a good way to flood the engine; if the choke is still operational, pressing the pedal once to the floor and then releasing it should set the choke and enrich the air-fuel mix for starting. If the engine get flood, holding the gas pedal to the floor will help dry out the plugs so they can fire again.
Not finding what you are looking for?

121 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

john h

Level 3 Expert

29494 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...