What is the cylinder head bolt torque settings (in ft/lb) for a toyota land cruiser 1HZ engine?

https://www.google.com/search?q=2012+chevrolet+captiva+2.2+VCDi+diesel+cylinder+head+torque+specs

https://www.google.com/search?q=2012+chevrolet+captiva+2.2+VCDi+diesel+big+end+torque+specs

Not too much information on the 2.2 diesel. A service manual is the best idea.

..

The torque settings for a Nissan Almera QG16 engine can vary depending on the specific component or fastener you are referring to. However, I can provide you with some general torque specifications for common components in the engine. Please note that it's always recommended to consult the manufacturer's manual or a qualified mechanic for accurate and up-to-date torque specifications. Here are some approximate torque values for certain components:

1. Cylinder head bolts: 25-30 Nm (18-22 lb-ft) initial torque, followed by an additional 90-degree clockwise turn (angle tightening).
2. Main bearing cap bolts: 25-30 Nm (18-22 lb-ft).
3. Connecting rod bolts: 15-20 Nm (11-15 lb-ft).
4. Crankshaft pulley bolt: 140-160 Nm (103-118 lb-ft).
5. Camshaft sprocket bolt: 85-105 Nm (63-77 lb-ft).
6. Intake manifold bolts: 15-20 Nm (11-15 lb-ft).
7. Exhaust manifold nuts/bolts: 25-30 Nm (18-22 lb-ft).
8. Spark plugs: 15-20 Nm (11-15 lb-ft).

Question edited for clarity and apparently it is a GXL not GLX.
Question moved to model category.

106 INCH Pounds, or 9 foot pounds.

2000 Toyota Land Cruiser 4.7L Engine Torque Specs

https://toyota-specs.com > cars > cruiser4.7 > torque-spe...
Valve Covers Installation The valve cover bolts torque down to 106 in-lbs or about 9 ft-lbs in a criss cross order. Be sure not to miss any bolts to avoid ...

1. Tighten the cylinder head bolts in the sequence shown. Using the 4 step torque turn method, tighten according to the following values:

• • Step 1: All to 34 Nm (25 ft. lbs.)
  • Step 2: All to 68 Nm (50 ft. lbs.)
  • Step 3: All to 68 Nm (50 ft. lbs.)

CAUTION: Do not use a torque wrench for the following step.
Step 4: Turn an additional 1/4 turn

• Step 5: Install and tighten bolts (1-10) in sequence shown, to 41 Nm (30 ft. lbs.) .

1. Tighten bolts (1-10) again to 41 Nm (30 ft. lbs.) PLUS 1/4 turn in sequence shown.
2. Install main bearing bedplate to engine block bolts (11-20), and torque each bolt to 28 Nm (20 ft. lbs.) in sequence shown.

Connecting Rod Cap Bolts 54 Nm (40 ft. lbs.) + 1/4 turn
1997 Jetta: Torque settings..vw..the head, fly wheel, big ends.


1997 Jetta3 1800 feul injection


Vibration Damper/belt Pulley
Tighten 20 Nm (14.8 ft lb) Crankshaft Toothed Belt Sprocket Tighten 90 Nm (66 ft lb) + 90° Camshaft Sprocket Tighten 80 Nm (60 ft lb) Main Bearing Cap
Tighten 65 Nm (48 ft lb) FLYWHEEL TORQUE
Torque 60 Nm. (44 ft. lbs.) + 1/4 turn (90°) [1] [1] Always replace bolts.
CYLINDER HEAD TIGHTENING TORQUE [1] :
1st sequence: 40 Nm (30 ft lb)
2nd sequence: 60 Nm (43 ft lb)
Final sequence: plus 1/2 turn (180°)
Here are some additional specifications, thanks
ntake Manifold
Mounting Bolts 25 Nm (18 ft. lbs.) Bearing Cap Nut 20 Nm (15 ft. lbs.) Rod Bearing Cap
Assembly
Tighten 30 Nm (22 ft lb) + 90° To measure radial clearance
Tighten 30 Nm (22 ft lb) but NOT additional 90° TIGHTENING SPECIFICATIONS
Oil Pump Bolt 20 Nm (14 ft. lbs.) Oil Tube To Block 10 Nm (7 ft. lbs.) Exhaust Manifold to Cyl. Head 25 Nm (18 ft lb) Exhaust Manifold to Front Exhaust Pipe 40 Nm (30 ft lb) Water Pump
TIGHTENING SPECIFICATIONS
Cover Bolts 10 Nm (7 ft. lbs.) Mounting Bolt and Studs 20 Nm (15 ft. lbs.) + 1/4 turn (90°) Pulley Bolts 25 Nm (18 ft. lbs.)

TIGHTENING SPECIFICATIONS
Connecting Rod Nuts:
Tighten In Two Stages:
First Stage 30 Nm (22 ft. lbs.) Second Stage turn an additional 90°(1/4 turn)

Here are some common torque settings for the Mazda Demio with the ZJ engine:

1. Cylinder head bolts - 35-40 Nm (26-30 lb-ft)
2. Main bearing bolts - 54-61 Nm (40-45 lb-ft)
3. Connecting rod bolts - 25-29 Nm (18-21 lb-ft)
4. Camshaft bearing cap bolts - 8-10 Nm (6-7 lb-ft)
5. Intake manifold bolts - 22-25 Nm (16-18 lb-ft)
6. Exhaust manifold bolts - 25-28 Nm (18-21 lb-ft)
7. Flywheel bolts - 78-85 Nm (58-63 lb-ft)

It's important to note that these torque settings may vary depending on the specific year and model of your Mazda Demio. Always refer to your vehicle's service manual for the correct torque specifications.

Torque setting Toyota Land-cruiser 80 Series 4.5 1995-98
Engine code: 1FZ-FE, 1HD.
Stage 1: 20 Nm (Start tightening bolts from center to outwards)
Stage 2: 39 Nm
Stage 3: Rotate each bolt by 90 Degrees.
Stage 4: Further rotate each bolt by 90 Degrees

Toyota 2c ...
USE NEW BOLTS...
Torque sequence:
You're driving a diesel single cylinder head engine. Engine head torque has to be done in specific order and stages if not can warp head or break bolts. Suggest you get torque sequence and torque specs from your Toyota dealer, they can give you correct answer. Don't trust answers on here, if you choose wrong specs. could end up messing up head.


Flywheel - Use a Sealer on bolt, Manual Transmission 88nm/65 ft lb... Auto Transmission 74nm/55 ft lb

BOLT INSTALLATION


Apply engine oil to the thread of the bolts and to the washers.
Tighten the bolts to the specified torque, using the tightening sequence shown.
Tightening torque: 54 ft-lb +/- 2 ft-lb
Loosen all bolts fully in the reverse order of tightening.
Re-tighten the loosened bolts to the specified torque in the tightening sequence shown.
Tightening torque: 15 ft-lb +/- 1 ft-lb
This step is to make it easier to ensure you are making 90 degree turns. Make a paint mark across each bolt head and cylinder head.
Tighten the cylinder head bolts 90 degrees in the specified order.
Tighten the bolts another 90 degrees in the specified order and check that the paint marks on the cylinder head bolts are aligned with the paint marks on the cylinder head.
Link to the guide for this engine: http://www.mivec.co.nz/tech/4G9x_Engine_Manual.pdf

cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.

Cylinder Head Torque Sequence

Tightening torque:
12 sided bolt
Step 1 ..... 34 Nm (25 ft lb)
Step 2 ..... Tighten an additional 90°
Step 3 ..... Tighten an additional 90°
Recessed head bolt ..... 18 Nm (13 ft lb)