Question about 1998 Mercury Villager

1 Answer

I have a 1998 mercury villager LS 3.0 , The wires going to my alternator, oil sensor and 02 sensor have melted together , my question is which wires go to each sensor ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mercury Master
  • 5,436 Answers

Peal back the protective wiring cover on the wires until you can see a color of the wire in both directions. Then match the wires.

Posted on May 09, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

its420_us

  • 316 Answers

SOURCE: where is a knock sensor for 1998 Mercury Villager located?

Here is a image of it's location, I hope it helps.
8262b2e.jpg

Posted on May 18, 2009

Anonymous

  • 17 Answers

SOURCE: o2 sensor wiring diagram

A new 02 sensor will come with new wires and connector. If not get back with me I think there is a repair kit for that problem.

Posted on Jun 01, 2009

emissionwiz

Marvin

  • 85206 Answers

SOURCE: ck engine light on code po335 p1336 also location of sensor?

P0335 and P0336 Engine crank sensor malfunction
To test this code, have a visual inspection of the location and wirings of the crank sensor. If the engine has a cam sensor, you might mistook it as the crank sensor (it is a good idea to contact ATS that can research this for you). Check the sensor wires for insulation making sure it is getting a voltage signal as shown in the wiring diagram. Sometimes, the wires itself is soaked with dirty oil causing the sensor to fail. If OK, check the engine timing belt system for any slack which can also cause the sensor to throw in the code. If all of these prove OK, remove the crank sensor and check it for resistance as compared to the standard specs. Lots of times, if the sensor probe end is contaminated with oil or cracked, this can only be revealed after the crank sensor is removed

Posted on Jun 02, 2009

Molson02536

Harvey N Tawatao

  • 3854 Answers

SOURCE: Code reader knock sensor where is it located

According to the Haynes manual it is under the intake manifold, Upper and lower intake manifolds must be removed for access. If you go to Auto Zone, they have the sensor and can give you the step by step instructions to replacing the knock sensor with common tools. Good luck and hope this help.

Posted on Sep 02, 2009

Jonah Oneal

  • 14092 Answers

SOURCE: My 1998 Mercury villager van 6 cylinder 3.0eng keeps cutting off

it could be faulty fuel pump or coil pack transistor.

Posted on Dec 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1998 Mercury Villager,its been smoking I got the oil channged thinking it was because my oil was low,its sti smoking and now.I have to jump start it ,if I want to drive it...do I need an...


If the smoke coming out (the back of the car exhaust) is dark grey...then you have a oil burning problem..this will cause your oil to be low sometimes quickly...if it is leaking out, sometimes oil leaks out on to exhaust under the hood, and can burn making smoke under the hood.. If the smoke is more white, then you have a head gasket problem. If you need to jump start your car, maybe you should drive to a national chain of auto parts store...they test batteries free...and test alternators free too...If you ran too low on oil, you might have a serious engine problem like a seized or nearly seized bearing, worn rings, or nearly seized motor.

Dec 08, 2014 | 1998 Mercury Villager

2 Answers

Code 0300 2000 Mercury Villager


Camshaft position sensor causing random misfire. Stuck EGR valve or clogged EGR ports.

Please comment on my info.

Mar 30, 2013 | 2000 Mercury Villager

1 Answer

Haw to repair cylinder no.6 misfire in mercury villager 1997


check the spark plug, the spark plug wire and the coil. those are the 3 things that can cause an ignition misfire.also check your oil and anti-freeze levels, make sure they are not mixing together.

Sep 23, 2011 | Mercury Villager Cars & Trucks

1 Answer

How to remove the dashboard on a 2001 mercury villager minivan?


go to villager quest yahoo group for help.

gerry

I have manuals for sale for $20 plus $5 postage, shop manual plu wiring book.

99-02 essentially the same. villager & quest identical vans.

Jul 31, 2011 | 2001 Mercury Villager

1 Answer

My 1998 Mercury villager van 6 cylinder 3.0eng keeps cutting off


it could be faulty fuel pump or coil pack transistor.

Dec 10, 2009 | 1998 Mercury Villager

1 Answer

Plz help


could be broken heater wire for O2 sensor. go here for files and pics for villager

http://groups.yahoo.com/group/villagerquest/

Jul 09, 2009 | 1997 Mercury Villager

1 Answer

CD changer wiring Diagram








here is premium radio cd98a9354.gif

Jan 05, 2009 | 1998 Mercury Villager

2 Answers

98 mecury villager knocking


rebuild engine ,or often a factory exchange unit is cheaper than a rebuild

Nov 29, 2008 | 1998 Mercury Villager

Not finding what you are looking for?
1998 Mercury Villager Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4388 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...