Question about 1998 Ford Windstar

Open Question

98 ford winstar 3.8 intake manifold runner control stuck open bank 2 were is it located? an will one work off a 97 ford F150 4.6

Posted by on

Ad

5 Suggested Answers

66 chrgr

mike loshbough

  • 1011 Answers

SOURCE: INTAKE MANIFOLD CONTRL RUNNER VAVLE LOCATIONS

they are on the back side of the motor just above the transmission .take off the dog house and you will see the unit.

Posted on Jan 25, 2009

Ad
warlock61

warlock61

  • 659 Answers

SOURCE: i have code 1538 on my check engine for 1998 ford windstar ,does

on the passenger side of the engine you will see 2 small metal rods at the top of the engine just below the intake manifold there are little white clips that hold the rods on these clips usually break and the rods come off

Posted on Mar 28, 2009

Ad

Jonah Oneal

  • 14092 Answers

SOURCE: 1998 ford windstar 3.8 with code p1538. Is this a

LOOKING IN CODE BOOK.POSSIBLE CAUSE TO YOUR PROBLEM THE IMRC COULD BE STUCK OPEN.OR THE IMRC ACTUATOR IS DAMAGED OR HAS FAILED.ALSO THE IMRC MONITOR SIGNAL CIRCUIT COULD BE SHORTED TO POWER GROUND OR SHORTED TO SIGNAL GROUND RETURN.

Posted on Oct 23, 2009

jturcotte

Jeffrey Turcotte

  • 8984 Answers

SOURCE: intake manifold runner control stuck

left rear of intake manifold, there should be a vacuum operated shaft that turns these throttle plates. You'll have to troubleshoot reason. Try turning shaft by hand. There is a vacuum switch that runs vacuum to both banks. I think it's behind the engine nearer the firewall.

Posted on Sep 01, 2010

pecadizo graciano

  • 109 Answers

SOURCE: intake manifold runner control stuck

intakes must be free from dirt or dust. check and clean the intake manifold runner.

Posted on Dec 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ford focus 2.3 litre DTC P2004 intake manifold runner control stuck open. What does it mean when it says shorted to VREF or signal circuit shorted open or shorted to VPWR.


code p 2004 refers to intake manifold air control actuator bank 1--actuator stuck open===causes --wiring--intake manifold air control actuator---mechanical fault
it also refers to intake manifold air control solenoid bank 1--solenoid stuck open=== causes --wiring---intake manifold air control solenoid---mechanical fault
reference auto data technical fault codes
I cannot find reference to the VREF or VPWR as they may be referenced in a ford workshop manual so you may have to ask a ford service person what they stand for but I suspect that they will come back to the same thing as listed in the causes

Feb 19, 2016 | Ford Cars & Trucks

2 Answers

2008 dodge avenger code p2004


Intake Manifold runner control stuck open - bank one:
- Intake Manifold Runner Binding Or Sticking
- Faulty Manifold flow valve
- Manifold flow valve harness is open or shorted
- Manifold flow valve circuit poor electrical connection

There is a factory service bulletin for this problem for 2007-2008 Dodge Avengers. (JS)

If you need further help, reach me via phone at https://www.6ya.com/expert/daniel_4061c3d97c12c4c7

Sep 22, 2015 | Dodge Cars & Trucks

1 Answer

How to fix code p2004 on 2005 ford focus


you code is here

P2004 Ford Intake Manifold Runner Control Stuck Open Bank 1


Possible causes - Intake Manifold Runner Control (IMRC) monitor signal shorted to power
- Faulty Intake Manifold Runner Control (IMRC) actuator
- Faulty Intake Manifold Runner Control (IMRC) solenoid
- Damage Powertrain Control Module (PCM)
- Blocked vacuum hoses
alt="What does this mean?"> What does this mean? Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light) P2004 Ford Description The P2004 is set when the Intake Manifold Runner Control (IMRC) is commanded closed by the Powertrain Control Module (PCM), but the IMRC indicates open.


Read more: http://engine-codes.com/p2004_ford.html#ixzz3lke1SreV

Sep 14, 2015 | Ford Cars & Trucks

2 Answers

P2004 code. where is the imrc valve located?


It is attached to the intake manifold, it is a valve that adjusts the runner length of the intake for optimal performance and fuel economy.

Jan 25, 2015 | 2006 Pontiac G6 GTP

1 Answer

Code p2004 saying intake manifold runner control sturck open. bank 1


code p 2004 has two references
intake manifold air control actuator , bank 1 --actuator stuck open====causes ---wiring---intake manifold air control actuator ---mechanical fault
second reference is
intake manifold air control solenoid , bank 1 --solenoid stuck open===causes ---wiring--intake manifold air control solenoid ---mechanical fault
probably means the same as what you have but in a more easy to understand method
--2012

Nov 26, 2017 | 2010 Dodge Caliber

2 Answers

Wants to die and spit and sputter after gets warm


Your engine has IMRC (intake manifold runner controls) that are supposed to stay closed under 3000 rpms. Over time they get carboned up and can hang open causing poor performance. Try to manually close the valve, if it immediately opens again the diaphragm might be bad. It would require replacing that IMRC.

Jan 10, 2018 | 1998 Ford Windstar

1 Answer

P1537 how do I fix this problem?


CODE P1537 - INTAKE MANIFOLD RUNNER CONTROL MALFUNCTION BANK 1 STUCK OPEN. POSSIBLE CAUSES. IMRC MONITOR SIGNAL CIRCUIT SHORTED TO POWER GROUND. IMRC MONITOR SIGNAL CIRCUIT SHORTED TO SIGNAL GROUND RETURN. IMRC ACTUATOR IS DAMAGED OR THE PCM HAS FAILED. - IMRC - IS INTAKE MANIFOLD RUNNER CONTROL.

Sep 01, 2011 | 1998 Ford Windstar

1 Answer

Intake manifold runner control stuck open on 1997 ford e250 bank 2


intakes must be free from dirt or dust. check and clean the intake manifold runner.

Dec 26, 2010 | 1997 Ford Econoline

3 Answers

1998 ford windstar 3.8 with code p1538. Is this a


LOOKING IN CODE BOOK.POSSIBLE CAUSE TO YOUR PROBLEM THE IMRC COULD BE STUCK OPEN.OR THE IMRC ACTUATOR IS DAMAGED OR HAS FAILED.ALSO THE IMRC MONITOR SIGNAL CIRCUIT COULD BE SHORTED TO POWER GROUND OR SHORTED TO SIGNAL GROUND RETURN.

Oct 23, 2009 | 1998 Ford Windstar

1 Answer

INTAKE MANIFOLD CONTRL RUNNER VAVLE LOCATIONS


they are on the back side of the motor just above the transmission .take off the dog house and you will see the unit.

Jul 30, 2008 | 1997 Ford Econoline

Not finding what you are looking for?
1998 Ford Windstar Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...