Removed wiper arm off the wiper motor shaft jeep 05 liberty, panel off door bolt off, but can't remover the motor. How do you remove the outer looks like rubber cup to seal the shaft from water entry

REMOVAL

1. Raise and support the hood.
2. Remove the windshield wiper pivot arms.
3. Remove the cowl top vent panels.

1. Disconnect the windshield wiper mounting arm and pivot shaft.

1. Remove the access cover from the dash panel.
2. Remove the mounting arm and pivot shaft retaining clip.
3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

1. Remove the windshield wiper motor.

1. Disconnect the electrical connector.
2. Remove the three bolts.
3. Remove the windshield wiper motor.

INSTALLATION

1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

1. Install the windshield wiper motor.

1. Place the windshield wiper motor in the dash panel.
2. Install the three retaining bolts.
3. Reconnect the electrical connector.

1. Reconnect the windshield wiper mounting arm and pivot shaft.

1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
2. Install the access cover in the dash panel.

1. Install the cowl top vent panels.
2. Install the windshield wiper pivot arms.
3. Adjust the windshield wiper pivot arms.

This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.



1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..



1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

REMOVAL

1. Disconnect and isolate the battery negative cable.
2. Remove the rear wiper arm from the rear wiper motor output shaft.
3. Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel .Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
4. Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel
5. Remove the bezel and gasket from the rear wiper motor output shaft.
6. Remove the trim panel from the tailgate inner panel.
7. Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
8. Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle
9. Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
10. Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
11. Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

To Install just reverse steps

1992-98 Vehicles

1. Disconnect the negative battery cable.
2. Remove the rear hood seal. Remove the wiper arm assemblies by raising the wiper blade off the windshield. Move the slide latch away from the pivot shaft and slowly lower the arm onto the latch. This unlocks the arm from the pivot shaft and holds the blade off the glass. Pull the arm from the pivot shaft.
3. Remove the cowl vent screws and disconnect the washer hoses from the washer jets.
4. Detach the electrical connectors from the wiper motor.
5. Remove the wiper assembly attaching screws, lift the assembly out and disconnect the washer hose.
6. Unsnap and remove the linkage cover.
7. Remove the wiper module assembly retaining bolts and remove the module from the vehicle.
8. Remove the linkage retaining clip from the motor operating arm by lifting the locking tab and pulling the clip away from the pin.
9. Remove the motor retaining screws and remove the motor from the vehicle.
10. The installation is the reverse of the removal.

Fig.: Lift up to release the clips and remove the hood-to-cowl weather strip



Fig.: Remove the cowl panel-to-firewall retaining clips



Remove the driver's side then the passenger side cowl panel from the vehicle






Fig.: Detach the electrical connector for the wiper motor

Release the wiper motor retaining clips and remove the cover from the vehicle






Fig.: Remove the wiper module assembly retaining bolts and remove the module from the vehicle






Fig.: Remove the wiper motor retaining bolts and ...





Fig.: ...remove the wiper motor from the vehicle




Hope helps (remember comment and rated this).

Front Wiper Motor Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove the windshield wiper mounting arm and pivot shaft
   WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
   NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
   
3. Remove the 3 bolts and the wiper motor.
   
   
   
   Fig. Wiper motor and linkage
   

To install:

1. Install wiper motor and bolts.
2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
3. Install windshield wiper mounting arm and pivot shaft.
4. Check wiper operation.

Rear Wiper Motor - Removal & Installation

1. Remove the rear pivot arm.
2. Remove the rear wiper motor shaft nut cover
3. Remove the rear wiper motor shaft nut.
4. Open the lift gate window.
5. Remove the rear wiper motor cover trim panel.
6. Disconnect the electrical connector.
7. Remove the 2 rear window wiper motor nuts
8. Remove the rear window wiper motor.
   
   
   Fig. Rear wiper motor view-2008 model shown, other years similar
   

To install:

1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
2. Reconnect the electrical connector.
3. Install wiper motor cover trim panel.
4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
5. Install shaft nut cover.
   
6. Check wiper operation.

Good luck (remember rated this post).

Removal & Installation To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Disconnect the battery ground cable.
3. Remove the wiper arms.
4. Remove the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to remove.
5. Remove the cowl vent screens.
6. Disconnect the electrical connector from the wiper motor and remove the 4 bolts that mount the module assembly to the cowl.
7. Remove the windshield wiper module from the vehicle.
8. Rotate the wiper operating arm in a clockwise direction to gain access to the bolt retaining the arm to the motor. WARNING
   Always rotate the wiper operating arm in a clockwise motion or damage to the motor could occur.
   
9. Remove the nut retaining the wiper operating arm to the wiper motor.
10. Remove the three wiper motor-to-wiper module assembly retaining bolts and remove the motor from the vehicle.

To Install:

1. Position the wiper motor on to the module assembly. Install the three wiper motor-to-wiper module assembly retaining bolts. Tighten the bolts to 115-151 in lbs (13-17 Nm).
2. Position the wiper operating arm on the wiper motor output shaft. Install the mounting nut and tighten to 22-29 ft-lbs (30-40 Nm).
3. Position the windshield wiper module onto the cowl. Install the mounting bolts and tighten to 106 in-lbs (12 Nm).
4. Connect the wiper motor electrical connector.
5. Position the cowl vent screens onto the inner panels. Install the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to install.
6. Install the wiper arms.
7. Connect the battery ground cable.
8. Adjust wiper arms if necessary.

Here is the picture of the motor....it is the round object in the middle of the picture that looks like a can and has a square block on the end of it.

You have to remove the cowl vent panel....just under the windshield. $64.00 for a new motor.

SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal

1. Disconnect the battery ground cable (14301).

1. Remove the windshield wiper pivot arms (17527).
   1. Remove the nuts (one each side).
   1. Remove the windshield wiper pivot arms.

1. Remove the LH and RH cowl top vent panels.
   1. Remove the hood weatherstrip.
   1. Remove the screws.
   1. Remove the retaining clips.
      • Disconnect the LH and RH washer hoses.

1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
   1. Remove the nuts.
   1. Remove the bolt.
   1. Position the windshield wiper mounting arm and pivot shaft assembly aside.

1. Remove the windshield wiper mounting arm and pivot shaft assembly.
   1. Disconnect the electrical connector.
   1. Remove the windshield wiper mounting arm and pivot shaft assembly.

----------------------------------------------------------------------------------------
Motor —Windshield Wiper Removal

1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .

1. Remove the windshield wiper motor (17508).
   1. Remove the output shaft bolt.
   1. Remove the bolts.
   1. Remove the windshield wiper motor.

Here is the procedure to remove the wiper motor. It says to remove wipers by removing the nut covers then remove the wiper nuts. Is this what your talking about?
If your talking about the wiper arms they just pop off at the swivel.
Use this link for info on removing blade assy.
http://www.autozone.com/az/cds/en_us/0900823d/80/04/f8/26/0900823d8004f826/repairInfoPages.htm

Wiper Motor
Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Park the wiper pivot arms in the highest position on the glass.
3. Disconnect the battery ground cable.
4. Remove the wiper pivot arm nut covers.
5. Remove the nuts and the wiper pivot arms.
6. Remove the cowl top vent panels.
7. Remove the four bolts, wiper mounting arm and wiper pivot shaft assembly.
8. Disconnect the electrical connector.
9. Remove the bolt and the windshield wiper motor operating arm from the motor.
10. Remove the three bolts and remove the windshield wiper motor.
11. To install, reverse the removal procedure.

This is what I Found there was not any Illustration's with it looks Fairly simple, Good luck



FRONT

1. Disconnect linkage assembly from wiper motor shaft.
2. Disconnect electrical connectors from wiper motor.
3. Remove wiper motor attaching bolts, then wiper motor.

REAR

1. Remove wiper blade and arm assembly.
2. Remove access panel on back door.
3. Disconnect linkage assembly from wiper motor shaft.
4. Disconnect electrical connectors from wiper motor.
5. Remove wiper motor attaching bolts, then wiper motor.

Skill
Level Mfg.
Warranty Standard Wiper Motor Labor Replace Front B 0.7 1.0
PLEASE DONT FORGET TO RATE ME Thank You Much

1. Remove the rear pivot arm; refer to Pivot Arm—Rear .
2. Remove rear pivot arm.
   1. Lift the pivot arm nut cover.
   1. Remove the nut.
   1. Remove the pivot arm.

1. Remove the liftgate door trim panel; refer to Section 501-05 . Remove the (A) liftgate handle to liftgate screws and the (B) liftgate handle. Remove the liftgate trim panel screw access plug. Remove the screw.
2. Remove the liftgate door trim panel.
   1. Use Windshield and Molding/Trim Removal Kit to remove the liftgate door trim panel from the liftgate window opening.
   1. Push the liftgate door trim panel toward the top of the liftgate and remove the liftgate trim panel.

1. Position the watershield aside to gain access to the rear wiper motor.

1. Remove rear wiper motor.
   • Disconnect electrical connector.
   • Remove three retaining bolts.
   • Remove rear wiper motor.

good luck.