SOURCE: remove driver's side door panel on 2002 nissan altima
Removal instructions are available with images and step by step directions, www.carstereohelp.com/strnissan.htm
SOURCE: changing headlamp for 2000 nissan altima
I just replaced the driver's side headlamp on my 2000 nissan altima. The manual advises you to take it to a dealer or details a long process which involves removing the bumper protector -- none of this is necessary. I am not mechanically inclined and a coworker and I did it on a lunch break. Here's how:
1) Disconnect the battery by loosening the nuts that attach both the positive & negative contacts.
2) Once loose, slide off the contacts. At the base of the battery (closest to front of the car) there will be another nut that you'll need to remove (this loosens a clip which holds the battery in place)
3) Once loosened, lift out the battery which will enable you to see the headlamp connection.
4) There is a white plastic ring that attaches to the headlamp connection. Twist this to the left (about a quarter turn).
5) Once you have loosened the white ring, you should be able to gently pull out the headlamp assembly.
6) Remove the headlamp from the socket by pushing on the plastic arm which will release the lamp from the socket (sounds confusing, but once you have the piece in your hand it will make sense)
7) Insert the new lamp into the socket & slide assembly back into the hole. Note. There is a groove in the assembly which will align with a notch in the headlamp frame...you can see this by looking through from the front of the headlight cover on the outside of the car.
8) Replace the white ring and twist to the right to secure in place.
9) Replace the battery & bolt you remove.
10) Replace the positive & negative connectors (hint: don't forget to replace the plastic battery cover before you attach the connectors).
Hope this helps...let me know how you make out.
SOURCE: need step by step instructions on how to remove a
Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.
SOURCE: Nissan Altima tring to change my transmission fulid and filter
thats why you have to remove the frame and for this you need an engine support and the average mechanic will charge you arround 100 bucks to do it
some rental stores have them some dont good luck eithor way you go but for god sake be carefull
SOURCE: How do you remove a 1999 Nissan Altima starter?
Nissan Car Altima & Sentra 1999-06
StarterRemoval & Installation
Negative battery cable
Air duct
Harness protector from the harness
Starter wiring at the starter
Starter-to-engine bolts
Starter from the vehicle
Fig. Starter location and mounting detail-3.0L Maxima with a
manual transaxle
Fig. Starter location and mounting detail-3.5L Maxima
To install:
Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on
Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short
bolt to 22-30 ft. lbs. (30-41 Nm)
Starter wiring
Harness protector
Air duct
Negative battery cable
Negative battery cable
Air inlet tube
Harness bracket
Wiring at the starter
Starter
To install:
Starter and torque the bolts to 60 inch lbs. (7 Nm)
Starter electrical connectors
Harness bracket
Air inlet tube
Negative battery cable
1.6L & 2.0L Engines
To install:
Negative battery cable
Wiring at the starter
Bolts attaching the starter to the engine
Starter
Starter and torque the bolts to 70 inch lbs. (8 Nm)
Starter electrical connections
Negaative battery cable
1.6L, 1.8L & 2.0L Engines
To install:
Negative battery cable
Wiring at the starter
Bolts attaching the starter to the engine
Starter
Starter and torque the bolts to 70 inch lbs. (8 Nm)
Starter electrical connections
Negative battery cable
1.8L & 2.0L Engines
To install:
Negative battery cable
Wiring at the starter
Bolts attaching the starter to the engine
Starter
Starter and torque the bolts to 70 inch lbs. (8 Nm)
Starter electrical connections
Negative battery cable
2.4L & 2.5L Engines
To install:
Negative battery cable
Air inlet tube
Harness bracket
Wiring at the starter
Starter
Starter and torque the bolts to 60 inch lbs. (7 Nm)
Starter electrical connectors
Harness bracket
Air inlet tube
Negative battery cable
2.4L Engine
To install:
Negative battery cable
Air inlet tube
Harness bracket
Wiring at the starter
Starter
Starter and torque the bolts to 60 inch lbs. (7 Nm)
Starter electrical connectors
Harness bracket
Air inlet tube
Negative battery cable
2.5L Engine
To install:
Negative battery cable
Air cleaner cover and duct
Harness bracket
Wiring at the starter
Starter
Starter and torque the bolts to 60 inch lbs. (7 Nm)
Starter electrical connectors
Harness bracket
Air inlet tube
Negative battery cable
3.5L Engines
Negative battery cable
Air cleaner case (upper) and air cleaner to electric throttle
control actuator tube.
Harness protector from the harness
Starter wiring at the starter
Starter-to-engine bolts
Starter from the vehicle
Fig. Starter location and mounting detail-3.5L engine
continue...
118 views
Usually answered in minutes!
×