04 lesabre rear hub bearing torque spec - 2004 Buick LeSabre

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

Should be 60 lb-ft (81 Nm) while rotating the hub occasionally to be sure the bearings aren't binding up. Also, lub the bearings well before torquing. From there you need to ratchet back 5 teeth/notches (1/8) turn on the hub nut for new bearings or 7 teeth/notches (1/6) turn on the hub nut for used bearings.

Hi Connie,just read your forum,here's a link to your rear hub bearing nut torque specs. http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f802d649d

Hub bearing torque specs for Kia Sorento 2011

http://www.autozone.com/autozone/repairinfo/specifications/specificationsMain.jsp?fromSearchPage=true&childCatName=Hub+Bearing+Torque+-+Rear&childCatId=23201245&categoryName=REAR+HUB+BEARING&childCategoryNameForTitle=

4-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake shoes
     
   • Rear halfshaft nut and loosen the halfshaft from the hub
     
   • Wheel hub and place it in a vise
     
   • Inner wheel bearing race from the hub
     
   • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
     
   • Parking brake cable from the steering knuckle
     
   • Brake line from the wheel cylinder and support the knuckle
     
   • Lower shock absorber nut
     
   • Lower ball joint by holding the ball joint stud
     
   • Upper ball joint
     
   • Coil spring while noting the location of the insulator
     
   • Steering knuckle cam
     
   • Steering knuckle
     
   • Snapring and press out the outer wheel bearing race from the knuckle
     

     Rear hub and bearing
     Click to Enlarge

To install:

1. Install or connect the following:
   
   • New wheel bearing into the steering knuckle
     
   • Snapring to the knuckle
     
   • Wheel hub
     
   • Steering knuckle cam and hand tighten the bolt
     
   • Coil spring
     
   • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
     
   • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
     
   • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
     
   • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
     
   • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
     
   • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
     
   • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
     
   • Brake shoes
     
   • Rear wheel
     
   • Negative battery cable
     
2. Fill and bleed the brake system.
   
3. Check and adjust the wheel alignment as needed.
   

2-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake drum
     
   • Wheel hub nut
     
   • Wheel hub
     
   • Inner wheel bearing race from the hub
     
   • Snapring
     
   • Wheel bearing outer race from the knuckle
     

     Rear hub and bearing
     Click to Enlarge

     Rear hub removal
     

     Inner wheel bearing removal-rear hub/bearing
     

     Rear wheel bearing removal-2wd
     

     Rear wheel bearing removal-4wd
     

To install:
Install or connect the following:

• Wheel bearing in to the knuckle
  
• Snapring
  
• Wheel hub into the wheel bearing
  
• Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  
• Brake drum
  
• Rear wheel
  
• Negative battery cable
  

  Rear wheel bearing installation
  
  hope this helps if so send testimonial comment or even any other questions you have
  

Well the torque for the three retaining bolts should be about 75-85 ft lbs.and the hub nut about 100 ft lbs.

Those are not nuts, they are bolts. The torque spec for those bolts is 52ft.lbs

the center bolt for cv axle!103ft-lbs,hub bearing assembly bolts!77ft-lbs

112 to 174 ft lbs