Question about 1997 Subaru Legacy

Open Question

How to remove the ignition lock and switch from a 1997 Subaru Legacy steering column ?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Rebgagnon

Mike Gagnon

  • 382 Answers

SOURCE: will 1999 subaru engine fit in 1997 subaru legacy?

Yes as long as the Motors are the same. You might need to have the computer out of doner car. Doors are suppose to fit 96 to 99.

Posted on Feb 01, 2009

Ad
mcgyver468

Mark L. Roberts Jr.

  • 710 Answers

SOURCE: Cause of noise in front differential of 1997 Subaru Legacy Outback.

there is a plug on the shaft-side of the differential. Using a ratchet remove the plug and with the engine OFF, stick your finger inside the hole and you should get fluid just below the threads of where the plug goes in.

Posted on Apr 24, 2009

Anonymous

  • 386 Answers

SOURCE: Steering wheel clicks on 1998 Subaru Legacy Outback wagon

steering column bearing sounds like a worn out steering column... jack the front wheels off the ground both sides relieve load on steering wheel to see if it lessens the amount of feel and noise, if it does it shoud be the column bearing, replace bearings or complete column,,, also try with the wheels off the ground and safely supported to manualy steer the wheels by hand and see if you feel in roughness or hear any noises,should some minor resistance but be smooth in it movement if everything suspension and steering component wise is in good working condition... please rate my help.. thanks...

Posted on Aug 05, 2009

Anonymous

  • 1 Answer

SOURCE: 2001 Subaru Legacy GT 2.5L SOHC

I don't think the dohc engine in your 97 will work. And I'm not saying that because I have a sohc engine for sale. It came out of my 2000 Impreza RS. Unfortunately my daughter totalled the car (she's OK) and I retained the vehicle from the insurance company. the car (and engine) had 120,044 miles at the time of death. the timing belt was done at 105,000. Email-eraronson@cox.net Talk to me-ED.A.

Posted on Jan 23, 2010

bjrich01

  • 5 Answers

SOURCE: where is the coolant temperature sensor/switch

While standing in front of the engine, look towards your back left engine area in the corner of the engine. You will have to take off the intake hoses/air box to see it. the sensor is sticking horizontal to the ground pointing towards the front of the engine. I used a little scope mirror to see it. It will have an automotive connector with a few wires running to it. The sensor should have a brown connector on it. If you need further assistance, type in google about the location and someone on there has taken really good pictures of it. I had to move some hoses and disconnect some wiring harnesses to get to it. Also, there is a relatively decent description in the Haynes manual for replacing it. Let me know how it goes! Should be about $30 at parts store.
BJ

Posted on Oct 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Subaru Legacy Marker lights won't turn off. My daughter just purchased this car at 3 today 4/15/11.


Check the switch on top of the steering column. It turns the marker lights on and off.

Apr 15, 2011 | 1997 Subaru Legacy

1 Answer

Need to replace ignition cylinder. no keys


This is not an easy repair due to anit theft requirements. need to chisel off bolts.

Section 11-04: Steering Column 1997 Probe Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000
Ignition Switch Lock Cylinder Removal
  1. Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the four lower steering column shroud screws.


    j5021c.gif

  1. Separate the upper and lower steering column shrouds.
  1. Remove the ignition switch lock cylinder illumination miniature bulb from the lower steering column shroud.
  1. Remove the upper and lower steering column shrouds.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal and installation procedure.
  1. If equipped, remove the ignition/shifter interlock cable screw.
  1. Disconnect the ignition/shifter interlock cable (3F719) from ignition switch lock cylinder (11582).
  1. Use a chisel to remove the two ignition switch lock cylinder bolts.
  1. Remove the ignition switch lock cylinder from the steering column.
  1. Disconnect the ignition key reminder switch electrical connector.
  1. If necessary, remove the ignition key reminder switch.


    j5028b.gif

Installation
NOTE: Use new ignition switch lock cylinder bolts. Tighten the bolts until the bolt heads break off. Check for proper ignition switch (11572) operation.

To install, reverse the removal procedure.

Mar 25, 2011 | 1997 Ford Probe

1 Answer

Remove ignition lock to switch link 1995 suburban


The ignition lock assembly contains two components: a lock cylinder to deter theft and an electrical portion that supplies power to electrical components such as the radio, electric windows, and windshield wipers. The electrical portion of the ignition switch also provides power to the starter motor to start the engine.
The ignition lock is an anti-theft device that prevents a vehicle from being driven unless the ignition key is in the ignition switch. If the ignition key is not in the ignition switch, it 's impossible to turn the steering wheel.
To replace the ignition switch cylinder lock, the trim panels around the steering wheel are removed. Then the tamper-proof hardware that attaches the ignition lock assembly to the steering column is removed. The ignition lock assembly is removed from the steering column, and the lock cylinder is replaced. The new ignition lock is reattached to the steering column, and the trim panels are replaced.make sure you dissconect battery first the 1997 had a recall on the ignition switch dont no if the 1995 had a recall if so they will replace for free

Dec 08, 2010 | 1995 GMC Suburban

1 Answer

Now to install igintion switch


Removal & Installation The ignition switch or warning switch can be replaced without removing the steering lock assembly. The ignition switch is on the back of the assembly and the warning switch on the side.
  1. Disconnect the negative battery cable and insulate the terminal end.

CAUTION The air bag system must be disarmed before removing the steering wheel. Failure to do so may cause accidental deployment, property damage or personal injury.

  1. Remove the steering wheel and the steering column upper and lower covers.
  2. Remove the spiral cable assembly.


23482ab.gif
View of the steering lock and ignition switch assembly

  1. Remove the combination switch from the steering column.
  2. Remove steering column support nuts and lower the steering column.
  3. Disconnect the ignition switch wiring and interlock cable (if equipped).
  4. Remove the bolts that secure the steering lock and remove steering lock assembly.
To install:
  1. Install the steering lock assembly and secure with new shear type bolts.
  2. Connect the ignition switch wiring harness and the interlock cable.
  3. Raise the steering column and secure with mounting nuts.
  4. Install the spiral cable assembly.
  5. Install the combination switch, steering column covers, and the steering wheel.
  6. Connect the negative battery cable and enable the air bag system.

May 23, 2010 | 1997 Nissan Maxima

1 Answer

How hard is it to change the Ignition Key Lock Cylinder? Do I need to take off the Steering wheel or does the guts just come out from the Steering Col with a pin, or something?


this is the oldest info I have. should be similar

Section 11-05: Steering Column Switches 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable. Remove the upper steering column shroud by removing the four or five self-tapping screws. Remove tilt steering column lock lever (if so equipped).
  1. Remove lower steering column shroud.
  1. Disconnect the ignition switch electrical connector.
  1. Rotate ignition switch lock cylinder to the RUN position.
  1. Remove the two screws retaining ignition switch.
  1. Disengage the ignition switch from the actuator.
Installation
NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.
  1. Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Check to ensure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install upper steering column shroud.
  1. Install the lower steering column shroud and tilt steering column lock lever (if so equipped).

Nov 06, 2009 | 1992 Lincoln Town Car

1 Answer

My 1999 subaru parking lights will not turn off


the rocker switch on top of your steering column is on.

Aug 26, 2009 | 1999 Subaru Legacy

1 Answer

Steering wheel clicks on 1998 Subaru Legacy Outback wagon


steering column bearing sounds like a worn out steering column... jack the front wheels off the ground both sides relieve load on steering wheel to see if it lessens the amount of feel and noise, if it does it shoud be the column bearing, replace bearings or complete column,,, also try with the wheels off the ground and safely supported to manualy steer the wheels by hand and see if you feel in roughness or hear any noises,should some minor resistance but be smooth in it movement if everything suspension and steering component wise is in good working condition... please rate my help.. thanks...

Aug 05, 2009 | 1997 Subaru Outback

2 Answers

Where is the ignition control module located on a 1990 Subaru legacy 2.2l


Center of firewall. It is a black plastic box with 2 screws or e the ignition module could be mounted below the steering column.

Jul 04, 2009 | Subaru Legacy Cars & Trucks

2 Answers

1997 Subaru Impreza wagon. Just replaced battery and hazard lights are blinking whether ignition is on or off. Tried turning hazards on and off and that didn't stop it. Only removing battery stops it. ...


Under your dash by steering column,by your left knee, is a small 4" x4" box that has a small wire attached. On the end of the wire is a small button. Push the button with the ignition in the on position. It will reset the alarm system. That will stop your lights from flashing. Have a great day.

Jun 14, 2009 | 1997 Subaru Legacy

Not finding what you are looking for?
1997 Subaru Legacy Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...