Need a passanger back door and a bench seat (2) row for 99 villager. Is there any that will interchange?

same way as you slight the front seat forwart.lift the bar up underneed the seats

is the belt wrapped around the lever to adjust the seat?
Try sliding the seat to get some slack.
He may have it in ALR mode. That is when you pull it allthe way out, and then it ratchets it's way back in until it is all the way in. Then it reverts back to pulling out and going in w/o ratcheting.
This is to lock a child seat in.
So, you need to get it in all the way somehow.

go here for more help.

Gerry

http://groups.yahoo.com/group/villagerquest/

THEY SHOULD BE BUT THE ANCHORS MIGHT BE DIFFERENT IN WIDTH MIGHT WANT TO CALL DEALER ON THAT ONE

Location of the spare tire and tools
The spare tire and tools for your vehicle are stowed in the following
locations:
Item Location
Spare tire Under the vehicle, just forward of
the rear bumper
Jack assembly Under the third row bench seat in
the tool bag
Removing the jack and tools
1. Lift the 3rd row seat cushion.
2. Remove the jack assembly from the bag under the seat.

Removing the spare tire
1. Open the liftgate, locate the U-shaped slits in the carpet, and flip up
the piece of carpet to expose the hex nut.
2. Insert the lug nut wrench on the
hex nut in cargo floor.
3. Turn the wrench
counterclockwise until tire is
lowered to the ground and the cable
is slightly slack.
4. Remove the retainer from the
spare tire. It may be necessary to
lift one end of the tire to disengage
the retainer

I have a third row seat available from a 1995 Caravan. Contact, [email protected].

it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal

1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
   

1. Slide the bench seat forward to the center row seating position.
   

1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.
   
   
   
   
   

1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.
   
   
   
   
   

1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.
   
   
   
   
   

1. Remove the bench seat from the vehicle through the body side door opening.
   

Yes...you can. I did this in my 05 Grand Caravan. We found ours at a local junk yard. It cost us 200 and even matched pretty well with the current benches. Just call around to your area junk/salvage people.

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.

fold top seat down first
then there is seat clip push seat forward with upward motion
this releases back floor clamps once released pull seat back this releases the front clamps then pull seat out of back door